DN: 3.175 mm - 50.8 mm
Pressure: 0 bar - 689 bar
... Available in 2 and 3 T port & L port configurations. Materials: SS 316, Duplex, Monel & Hastalloys. Floating ball design ensures leak proof shut-off at high pressure. Seat options: Delrin, PTFE, PEEK & KEL-F. Anti blow-out internally loaded ...
DN: 3.175 mm - 25.4 mm
Pressure: 0 bar - 1,379 bar
Temperature: 0 °C - 538 °C
... Materials: SS 316, Duplex, Monel & Hastalloys in forged & bar stock construction. Variety of end connections: Male & Female NPT, BSPP, BSPT, ISO tapered pipe ends & PANAM® tube fittings Non-Rotating vee tip / Ball tip provides repetitive & leak ...
DN: 12.7 mm - 19.05 mm
Pressure: 0 bar - 689 bar
Temperature: -273 °C - 538 °C
... Materials: SS 316, Duplex, Monel & Hastalloys. Non-Rotating vee tip / ball tip provides repetitive & leak tight shut-off. Available with soft seat option. NACE certification available upon request. Heat code traceability. ...
DN: 1.6 mm - 3.2 mm
Pressure: 100 psi
... Beswick selector valve can be used as a quiet replacement for solenoid valves in many applications, and has the ability to operate from a servo motor. The SVPC series rotary selector is a variation of the SV, with integral ...
DN: 4 mm
Temperature: -18 °C - 93 °C
... sensing technology • Direct valve-to-vacuum cup mount Note: These valves are designed to not seal shut completely. This purposeful small vacuum loss allows the valves to have immediate vacuum when ...
DN: 3.18 mm - 14.27 mm
Pressure: 1.4 bar - 6.9 bar
... needle
valves are equipped with a V-tip for rapid opening and closing. For flow regulation, hand-operated needle
valves with regulating tips are recommended.
Technical data
Nominal diameter: 3.18 mm
Valve ...
DN: 3.18 mm
Pressure: 1.4 bar - 6.9 bar
... requirements
Note
For flow regulation, manually operated needle valves with regulating tips are recommended; the ...
DN: 100 mm - 3,000 mm
Pressure: 16, 10, 25 bar
Temperature: -40 °C - 200 °C
... be used as a safety valve (positive safety valve able to close even in case of tampering) In addition to the above mentioned technical advantages there is a remarkable economical benefit as this valve ...
Temperature: 32 °F - 230 °F
... check valve flow controls are typically used to control air flow from air cylinders, thereby controlling the speed at which the piston strokes, either while extending or retracting, depending on their location in the circuit. Flow ...
... T-EAV 912 series electric actuated PVC body is a on-off and proportional controlled electric actuated ball valve. The body is made from aluminum material. The housing is compose of aluminum alloy. The body and housing ...
Temperature: -10 °C - 95 °C
... Tork's T-PKV .W812 is a butterfly valve which is made up of PVC with an extensive pressure of 10 bar and a maximum temperature that ranges from -10 up to 95° C. The unit has EPDM,VITON for its seal. The butterfly valve ...
Pressure: 16 bar
Temperature: 0 °C - 80 °C
... The T-PAV 913 features PVC body it has 2/2 way,double acting actuated ball valve. The brand of the product is TORK. The minimum pressure is 0 and goes up to 16 bar. The minimum temperature is 0 and goes up to 80 C. lastly, ...
DN: 3 mm - 12 mm
Pressure: 0.1 MPa - 0.9 MPa
Temperature: 0 °C - 60 °C
... The most standard Speed Control Valve for driving devices. The tube lead-out directions are free. The resin body rotates and the tube lead-out direction can be changed. For Free type, the fitting part rotate. For Free type, the ...
DN: 4, 8, 6, 12, 10 mm
Pressure: 0 MPa - 0.9 MPa
Temperature: 0 °C - 60 °C
... Best suitable for high-speed drive cylinder. Possible to control high-speed cylinder. Exhaust needle valve type, whose exhaust port incorporates throttling function, is available. Tube O.D. 3mm is available for mini type. Annual ...
DN: 10, 8, 12, 6, 4 mm
Pressure: 0 MPa - 0.6 MPa
Temperature: 0 °C - 60 °C
... Pressure control valve saves compressed air consumption. In driving an actuator under high pressure, compressed air can be saved by use of the pressure controller to reduce the pressure only during home return. Controls the pressure ...
DN: 0.125, 0.375, 0.5 in
Pressure: -1 bar - 20 bar
Temperature: -20 °C - 84 °C
... Resolution Valve provides superior performance over legacy needle valves. Selection of stainless steel 316L, aluminum or PEEK body material. The high resolution electronic flow control valve The High ...
DN: 6, 8 mm
Pressure: 20 psi - 30 psi
... Miniature Pinch Valve is a solenoid operated device that is designed to open and close tubes for controlling flow of liquids and gases. Other valve types have internal passages that may cause small amounts of fluid to ...
DN: 12 mm - 44.3 mm
Pressure: 3 bar
Temperature: -5 °C - 100 °C
... cylinder) valve, also known as B-type valve, the cylinder directly drives the valve plate, seal material Viton or Teflon-PTFE selections. Long life, high flow, resistant to air pollution, can replace ...
DN: 63 mm - 100 mm
... Inline manual ball
valve for ISO-K flanges, designed to ensure handling and sealing in vacuum applications. The product is available in multiple sizes (DN) with AISI 304 flanges and variants with Teflon® (PTFE) seals.
Available ...
DN: 10 mm - 50 mm
... Manual inline ball
valve equipped with AISI 304 flanges and Teflon® seals. Natural finish.
Main details
- Line: KF
- Line type: KF
- Product type: Valves
- Finish: Natural
- Materials:
DN: 0.5 in - 2.5 in
Pressure: 3.5 bar - 8 bar
Temperature: -10 °C - 180 °C
... Angle Seat Valve with Plastic Operator (NC/NO/Double Acting) > Body Material: - SS ASTM A351 Grade CF8 / CF8M > Seal: - PTFE / PEEK / VITON Actuator Information > - Cover: Nylon Glass-Filled (Corrosion résistive) ...
DN: 2.5 mm
Pressure: 3 bar - 10 bar
Temperature: 0 °C - 140 °C
... AVS Römer pressure relief valves are used for protection in closed circuits. When the set response pressure is exceeded, the valve opens and discharges the fluid. ...
AVS Römer
DN: 0.25 in - 8 in
Pressure: 1,494 psi
... requirements provides a sufficient safety factor during operation. A special hybrid seat design is comprised of a metal housing and polymer insert machined as a single unit provides bubble tight shut-off (Rate A), combined with lower ...
HABONIM
DN: 15 mm - 50 mm
Pressure: 10 bar - 40 bar
Temperature: -50 °C - 270 °C
... PFA-lined flanged ball valve PN 10 -PN 40, class 150 with full bore. The material combination stainless steel 1.4408 (From DN 65 body made of steel epoxy coated, stainless steel upon request) on the outside and PFA fluoropolymer as lining ...
DN: 10 mm
Pressure: 0.3 bar - 10 bar
Temperature: 5 °C - 60 °C
... incorporating a normally closed servo-controlled solenoid valve upstream of the float valve, but in the same body, this acts as the shut off to the supply line. This combined valve allows other equipment ...
A. u. K. Müller
DN: 15 mm - 100 mm
Pressure: 16 bar
Temperature: 0 °C - 60 °C
... EFFAST PVC-U valve BK1 is a true union ball valve ideal for heavy duty applications, chemical applications and water treatment. Technical features: Solvent welded sockets (ISO, BS, ASTM, JIS), threaded sockets (BSPP ...
Effast
DN: 15 mm - 100 mm
... Model No.: CQ100-Socket, CQ200-Thread, CQ300-Flanged Specifications: Body Material:UPVC,PP,CPVC,PVDF Seat:PTFE(TEFLON) O-Ring:EPDM,VITON(FPM) Size: DN15(1/2")~DN100(4") Standard: JIS,ANSI,DIN ...
Shie Yu Machine Parts Industrial Co., Ltd.
DN: 1.25, 1.5, 2 in
Pressure: 0.3 bar - 7 bar
Temperature: 0 °C - 60 °C
... VORTEX float valve the HighFlow valve with 600l/min. Diaphragm pilot valve with float for automatic filling of water troughs, tanks and cisterns with large volumes. VORTEX float valves ...
PVA Schwimmerventile GmbH
DN: 1.25, 1.5, 2 in
Pressure: 10 bar
... BALL VALVE PN10 with female thread connection Rp, EPDM and PTFE O-ring, ABS sphere Connectivity standard Internal thread GAS ISO 7/1 Colors Black (RAL 9011) ...
Bucchi S.r.l.
DN: 20 mm - 63 mm
Pressure: 10 bar
... PTFE tape recommended for threads sealing. Technical features • Polypropylene compression nut. • HDPE seats. • EPDM O rings. • Dimensions complying with EN ISO 1452 : Plastics piping systems for water supply ...
DN: 20 mm - 90 mm
Pressure: 16 bar
Temperature: 0 °C - 60 °C
... This device is a three piece, full-bore valve that is suitable for water distribution particularly in swimming pools. It contains a PP handle, double EPDM o ring. It has recorded an Ap maxi that can hold up to 3 bars. ...
SFERACO
DN: 2.5 in - 20 in
Pressure: 235 psi - 350 psi
Temperature: -10 °C - 130 °C
... ductile iron flow balance valve adopts low-resistance Y-shaped structure, the shell is coated with epoxy resin. Flow measuring fittings on both ends feature good self-sealing performance and easy adjustment. The highly precise valve ...
Taloar
DN: 1 mm
Pressure: -70,000 Pa - 200,000 Pa
Temperature: 5 °C - 80 °C
... only to proportional valves. The advantages of minimal space occupancy, fast response, small internal diameter, and small influence on fluidic system fluctuations are definitely your best choice. Feature of SD61 2-Way Miniature Valve Structural ...
DN: 3.175 mm
Pressure: 0 bar - 5.2 bar
Temperature: 0 °C - 66 °C
... eight turns to full open Description MVT™ Metering valves are constructed of PTFE and PEEK materials. Non-fluid contacting external parts are made of anodized aluminum. Valves are offered in three conveniently ...
Aalborg Instruments
DN: 10 mm - 50 mm
Pressure: 16 bar
Temperature: 0 °C - 80 °C
... Radial installation or removal Double sided blocked ball Full sectional area of flow Seal materials - EPDM, FPM Ball seating joint - PTFE Connections - flange, PE fusion socket, PE fusion spigot, solvent socket, solvent spigot, threaded ...
Praher Plastics Austria GmbH
the best suppliers