DN: 0.25 in
Temperature: -30 °C - 80 °C
... Flow control 90° (bidirectional) Fluid Temperature: -30°C (-22°F) to 80°C (176°F) Female Thread: 1/4 ...
DN: 0.063, 0.125 in
Pressure: 0.5 psi - 100 psi
Temperature: 40 °F - 120 °F
... Pressure piloted 3 Way Valves apply signal pressure to a diaphragm that is opposed by a spring force. When then pressure signal force is greater than the spring force it reaches its set-point (also called “On” pressure), the internal ...
AIR Logic
DN: 0.063, 0.125 in
Pressure: 0.5 psi - 100 psi
Temperature: 40 °F - 120 °F
... connection available on the exhaust port. When the valve trips, the supply is open to the output port and the exhaust is closed. There is no connection available on the exhaust port. The valve will remain in this ...
AIR Logic
DN: 0.625, 0.125 in
Pressure: 22 psi - 116 psi
Temperature: 40 °F - 120 °F
... port is open to the output port. When the valve trips, the supply is shut off and the output port is vented through the exhaust to atmosphere. There is no connection available on the exhaust port. The valve will remain ...
AIR Logic
DN: 0.5 in - 2.5 in
Pressure: 3.5 bar - 7 bar
Temperature: -10 °C - 180 °C
... Body Material - SS ASTM A351 Grade CF8 / CF8M / CF3M Seal - PTFE / VITON Circumstance Temp: -10°C to 70°C Actuator Information > - Life: More than ten million cycle > - Other Technical Data: Available Available on request Adjust Stroke Limiter ...
UFLOW AUTOMATION
DN: 0.5 in - 2.5 in
Pressure: 3.5 bar - 8 bar
Temperature: -10 °C - 180 °C
... Angle Seat Valve with Plastic Operator (NC/NO/Double Acting) > Body Material: - SS ASTM A351 Grade CF8 / CF8M > Seal: - PTFE / PEEK / VITON Actuator Information > - Cover: Nylon Glass-Filled (Corrosion résistive) with SS Liner > ...
UFLOW AUTOMATION
DN: 0.5 in - 2.5 in
Pressure: 3.5 bar - 8 bar
Temperature: -10 °C - 180 °C
... Body Material - SS ASTM A351 Grade CF8 / CF8M / CF3M Seal - PTFE / PEEK / VITON Cover - Nylon Glass-Filled (Corrosion résistive) with SS Liner Plate - NBR / VITON Life - Three Million Cycle Tested Other Technical Data - Available on Request - Adjust ...
UFLOW AUTOMATION
DN: 50 mm - 600 mm
Pressure: 25 bar
Flow rate: 16 m³/h - 5,400 m³/h
... PRESSURE SUSTAINING VALVE The valve maintains downstream pressure over a pre-set minimum value, regardless of fluctuating flow or varying upstream pressure. Otherwise the valve may open gradually ...
Tecnidro
DN: 50 mm - 600 mm
Pressure: 25 bar
Flow rate: 16 m³/h - 5,400 m³/h
... ALTITUDE CONTROL VALVE This valve controls water level in high level reservoirs to avoid overflow, without any external control system like float control etc. The valve remains completely open until ...
Tecnidro
DN: 50 mm - 600 mm
Pressure: 25 bar
Flow rate: 16 m³/h - 5,400 m³/h
... EXCESSIVE FLOW VALVE The valve avoids reservoir emptying and flooding dues to casual pipeline failure. The valve is controlled by a differential hydraulic pilot that senses flow speed closing completely ...
Tecnidro
DN: 10, 15, 8, 25, 20 mm
Pressure: 63 bar
Temperature: -20 °C - 150 °C
... MINI BALL VALVE - FEMALE / FEMALE BSP - REDUCED BORE - STAINLESS STEEL 316 ...
BENE INOX
DN: 8 mm - 50 mm
Pressure: 55 bar
Temperature: -20 °C - 150 °C
... 1 PIECE BALL VALVE - FEMALE / FEMALE BSP - REDUCED BORE - LOCKABLE HANDLE - STAINLESS STEEL 316 ...
BENE INOX
DN: 8 mm - 50 mm
Pressure: 63 bar
Temperature: -29 °C - 175 °C
... 2 PIECES ATEX BALL VALVE - FEMALE / FEMALE BSP OR NPT - FULL BORE - LOCKABLE HANDLE - STAINLESS STEEL 316 ...
BENE INOX
Pressure: 16 Pa
Temperature: -10 °C - 180 °C
... PP1020 Series Normally Closed ; PP1021 Series Normally Open Advantage of TORK Pneumatic Piston Valves ● Less pressure drop than the globe valves ● Short open-close time ● High flow rate ● Body and actuator ...
DN: 10 mm - 100 mm
Pressure: 6 bar
... consumption! Air operated Pinch Valves with Internal Thread Connection - VMC Series The air operated pinch valves of the VMC series are available in the nominal diameters of DN10 to DN100. They are ...
AKO ARMATUREN
DN: 10 mm - 50 mm
Pressure: 4.5, 6 bar
... AKO air operated Pinch Valves with Internal Thread Connection - VMP Series The air operated pinch valves of the VMP series are available in the nominal diameters of DN10 to DN50. They are designed ...
AKO ARMATUREN
DN: 10 mm - 50 mm
Pressure: 6 bar
... the VM series pneumatic pinch valves can also be offered with alternative individually customised connections. For information on advantages of AKO pinch valves and their functions, see air operated pinch valves. Pinch ...
AKO ARMATUREN
DN: 50 mm - 150 mm
Pressure: 0 psi - 60,000 psi
... overview
The normally closed air-operated
valve is rated to 60,000 psi and designed for remote pneumatic actuation with spring-return fail-safe operation. Its 316 stainless steel body and UNF
threaded connections ...
Pressure: 7 bar
Temperature: -10 °C - 100 °C
Flow rate: 0 l/min - 250 l/min
... Product Summary
The WL 2832 proportional air
valve is engineered for precise airflow and pressure control in medical devices. Adjustable via solenoid current, it provides smooth, infinitely variable regulation with fast response ...
Pressure: 0.2 bar - 8 bar
Temperature: 1 °C - 75 °C
Flow rate: 12, 17, 35 l/min
... Product Overview
A urinal flush
valve designed for commercial and public restroom systems to control flushing cycles, reduce water consumption and provide reliable performance across variable inlet pressures. Available in manual, ...
DN: 6 mm - 6 mm
Pressure: 1 bar - 1 bar
Temperature: -10 °C - 100 °C
... Overview
The WL3050 double pinch
valve is a tube-control
valve that regulates liquid or air flow by mechanically compressing a flexible tube. The fluid never contacts the
valve mechanism, ensuring ...
DN: 0.5 in - 1 in
... Hyperr Valves Pvt Ltd is a leading manufacturers, supplier and exporter of Pressure Reducing Valves. Our Pressure Reducing Valve is engineered to automatically reduce a high, fluctuating inlet pressure ...
Hyperr Valves Private Limited
DN: 0.5 in - 6 in
Pressure: 0 bar - 60 bar
... Hyperr Valves Pvt Ltd is a leading manufacturers, supplier and exporter of Pressure Reducing Valves. Our Pressure Reducing Valve is engineered to automatically reduce a high, fluctuating inlet pressure ...
Hyperr Valves Private Limited
DN: 0.5 in - 6 in
... Hyperr Valves Pvt Ltd is a leading manufacturers, supplier and exporter of Pressure Reducing Valves. Our Pressure Reducing Valve is engineered to automatically reduce a high, fluctuating inlet pressure ...
Hyperr Valves Private Limited
DN: 0 mm - 10,000 mm
... Way Foot Pedal Valve BSP 1/4" — Standard — £22.97
DN: 0 mm - 10,000 mm
Pressure: -1 bar - 20 bar
Flow rate: 18 l/min - 5,000 l/min
... Steel; IP52
Technical specifications
- Series: FC Series
- Valve type: Stepper-controlled proportional needle valve
- Repeatability: ±0.1% F.S.
- Control signals: 0–10V,
DN: 6.35 mm - 50.8 mm
Pressure: 0 psi - 2,000 psi
Temperature: -20 °C - 180 °C
... Product Overview
The two-piece high-pressure ball
valve is engineered for industrial service up to 2000 PSI. Body in CF8M stainless steel, available with PTFE or RTFE seats and a blow-out proof stem for secure operation.
Specifications ...
MARSVALVEUK
DN: 3.175 mm - 50.8 mm
Pressure: 0 bar - 137.9 bar
Temperature: -20 °C - 180 °C
... Product overview
A complete range of non-maintainable 1-piece reduced-bore ball
valves in CF8M stainless steel. Economical, compact and reliable with blow-out proof stems, insulated grips and lockable lever handles. Investment ...
MARSVALVEUK
DN: 8 mm - 50 mm
Pressure: 0 psi - 1,000 psi
Temperature: -20 °C - 100 °C
... Overview
- Product name: Economical Three-Piece Ball Valve
- Brand: MARS Valve
- Category: Three-piece ball valves for industrial on/off service
- Design: three-piece
MARSVALVEUK
DN: 12.7 mm - 25.4 mm
Pressure: 0 bar - 689.5 bar
Temperature: -50 °C - 200 °C
... Standard hex head bleed
valve; internal hex (hex socket) bleed
valve.
Application Scope
Draining, venting and pressure relief for ball
valves, gate
valves, wellhead trees, ...
Pressure: 0 bar - 40 bar
Temperature: 95 °C
... Externally controlled valve for the hydrogen sector Valves for hydrogen and oxygen in electrolyser operation Pneumatically operated 2/2-way valve - Direct pressure control Designed for electrolysers - ...
DN: 10 mm - 65 mm
Pressure: 6 bar - 10 bar
Temperature: -20 °C - 130 °C
... Free-flow pneumatic valves are essential components for controlling and intercepting the flow of numerous types of fluids that can be found in various industrial sectors. Choosing which type of valve to use is related ...
DN: 15 mm - 100 mm
Pressure: 5 bar - 10 bar
Temperature: -10 °C - 180 °C
... indicator • - Tilting shutter with PTFE-C755 seal (Teflon + Graphite 30%) • - Wide range of accessories: Namur solenoid valves, magnetic, inductive, pneumatic, electromechanical sensors, stroke limiting devices, handwheel for manual ...
DN: 25 mm
Pressure: 40, 25, 16 bar
Temperature: -20 °C - 120 °C
... Ball valves, unlike the types of valves previously mentioned, use an opening and closing action. Thanks to a specific valve, moreover, it performs a rotation limited to an angle of 90°. Ball valves ...
DN: 10 mm - 50 mm
Pressure: 0 bar - 10 bar
Temperature: -20 °C - 150 °C
... the diameter of the pipe High flow capacity 2. Pneumatic actuator integrated in the valve Space saving (-60%) and reduced costs compared to an automated valve 3. Piston with chemical nickel plating Lower wear ...
OMAL Spa
DN: 3 mm - 12 mm
Pressure: 0 bar - 10 bar
Temperature: 0 °C - 70 °C
... Compact needle valve in aluminium housing Leak-free valve Spring loaded, non rising adjustment stem with 56-pitch thread provides smooth, non-reversing flow characteristics and 15-turn resolution Non-rotating ...
Mass Flow ONLINE BV
DN: 0.5 in
Pressure: 0 psi - 5,000 psi
Temperature: 70 °F - 1,000 °F
... This globe control valve features a 1/2" body with 150 lb ANSI raised face flanges. It is designed to fit directly into pipelines of the same flange size and rating. Its compact size and light weight make it especially suited to modulating ...
Badger Meter
DN: 6.35 mm - 38.1 mm
Pressure: 700, 1,034 bar
... Design Threaded body Automation-ready with standard ISO 5211 connecting plate Total HermetiX Integrity package with: ISO 15848-1 and API 641 emission standard certificated design ISO 10497 and API607 fire-safe standard certificated ...
HABONIM
DN: 8 mm - 80 mm
Pressure: 63 bar
Temperature: -50 °C - 180 °C
... Two-piece stainless steel ball valve with screwed ends. Low pressure loss due to full and extremely smooth passage. Blow-out proof switching shafts are inserted from the inside. The ball valve does not require any maintenance ...
GEFA Processtechnik
DN: 6, 14, 8, 10 mm
Pressure: -1 bar - 20 bar
Temperature: -30 °C - 130 °C
... FEMALE RP ISO 7 - FEMALE RP ISO 7 VALVE The GHILUX miniature ballvaves have been created and engineered by Aignep in the 90’s. The supercompact dimensions and the excellent performance respond to the growing demand of miniaturization. Many ...
AIGNEP
DN: 0.375 in - 2 in
Pressure: 0.2 bar - 20 bar
Temperature: -60 °C - 225 °C
... resistant stainless steel provides a solution. The sealed and gas-tight design covers an even wider application range. The valves can be conveniently adjusted or aligned using the external adjustment, which means that perfect alignment ...
Goetze KG
DN: 4 mm
Pressure: 0 bar - 300 bar
Temperature: -20 °C - 70 °C
... The diaphragm shut-off valve HP 550 is laid out for the use in pure gas supply systems. The diaphragm shut-off valve has 3 inlets and one outlet. Threaded holes on the reverse side connect to a bracket ...
Hornung GmbH
DN: 15 mm - 50 mm
Pressure: 0 bar - 138 bar
Temperature: 0 °C - 260 °C
... Thread end connection resilient seated 2 piece ball valve An economical manual operated valve rated to 138 bar/2000 psi Features Robust engineering design High quality Benefits Long service life Bubble ...
Metso Automation
Pressure: 5,000, 3,000 psi
Temperature: 0 °F - 225 °F
... Use to slowly or quickly bleed pressure from a line after a calibration is complete • Easily connect between the end of a Quick-test hose and the process connection • Keep fluid or contaminates out of the hand pump, calibrator or nitrogen control ...
the best suppliers