|
|
|
|
|
|
ABM helical geared motors, shaft mounted helical motors and planetary back geared motors give added power to the motor torque and reduce the speed to the necessary level. Helical geared motors and shaft mounted helical motors are those most widely used in industrial applications.
These ABM drive units are particularly known for their:
energy saving of 98% efficiency at each stage
economy due to favourable cost/performance ratio
rugged and practically maintenance-free
environment friendly drive type (compared with internal combustion engine, hydraulics, pneumatics)
The high-quality helical gearing with polished tooth profiles guarantee complete smoothness of operation and accurate power transmission.
ABM Helical Geared Motors
a shaft height of 71 mm to 315 mm
drive torque of 30 to 6000 Nm
rpm from 2 to 750 rpm
ABM Shaft Mounted Helical Motors
drive torque up to 2500 Nm
speed from 3 to 220 rpm
reduction ratios of 6 to 250 to 1
ABM Planetary Geared Motors
drive torque up to 700 Nm
reduction ratios, single stage up to i = 12
all further details upon enquiry
|
|
KEB COMBIGEAR S Helical Worm Geared Motors
The KEB helical worm geared motors are available in the power range 0.12…12kW representing the “standard gear" in machines and systems due to their superior economic efficiency.
Lifetime lubrication, universal mounting construction and varied output options (solid shaft, hollow shaft) make this geared motor extremely adaptable
|
|
|
|
|
|
SEW-Eurodrive's S-Series gearmotors (right angle) offer helical-before-worm gearing combining durability with power-packed performance in a compact design that requires no motor belts or couplings.
-Reducers
Worm shaft and helical gears manufactured from certified steel, heat treated to a case hardness of 58-62 Rockwell C for long gear life
Gears are milled, hardened and ground to assure maximum efficiency (up to 94%), minimum noise and heat generation
High capacity anti-friction bearings for optimum load carrying capacity and long life
Captured keys on input and output shafts
Gearcases made of high strength gray cast iron, SAE Class 30
High cross-section modulus design with stiffening webs for maximum rigidity
S-Series reducers are continuous duty at rated thermal capacity, based on ratio and input speed
Center tapped holes on output shafts
Double output seal design consisting of patented bi-helix inner seal made of Viton® and double-lip Nitrile (Buna-N) outer seal*
-Motors
NEMA Design B/C
Inverter duty
Connection terminals
Extremely low motor inertia
Mark for shipment into Europe
|
|
Efficient compact right-angle geared motor. A favorably priced alternative for the standard tasks expected of a right-angle drive.
- Sizes:
- S0 – S4.
- Rated torque:
- 23 – 800 Nm.
- Motor power:
- 0.12 – 9.2 kW.
- Gear ratio range:
- 6 – 683.
|
|
Worm gear units up to 20 Nm
Fed up of compromises or expensive customized gear motor solutions? Have a look at HeiDrive - the intelligent gear motor programme!
Configurate a gear motor perfectly adapted to your needs and requirements by choosing from different gear sizes, a variety of ratios
and a broad range of motor types and accessories. Whether you are in need of helical gears, helical bevel gears or worm gears -
HeiDrive always offers you the right choice!
Following ratios/torques are available:
Size S031 S031
Ratio i 7,0 up to 100,0 : 1 7,0 up to 100,0 : 1
Torque Mzth [Nm] up to 6 up to 6
Combination with motor type 3 phase motor 3 phase motor
Motor power P2 [W] 30 - 80 30 - 80
Motor speed [rpm] 2700 2700
|
|
Gear motor with worm screw and standard motor Ø 37x34 24 Vdc 5000 RPM output W, with noise suppressor.
Driving shaft mounted on two bearing and bushing. Outlet shaft supported by two bearings.
Design to give low RPM in little dimension
* The rotation speed can change of ± 10%.
The S1 load test was made using a 0,8 A corrent in the air with an increase of temperature of 70 C°
The S2 load test was made using a 1,5 A corrent in the air with a timing 5' ON 5' OFF with an increase of temperature
of 80 C° max
The starting corrent is 4 A and cannot be maintained for more than 2"
Max forces wich may act on the outlet shaft: Axial 25 kg, Radial 40 kg
It is possible to apply an encoder.
|
|
Series C Right angle helical worm geared motors and reducers provide a highly efficient and compact solution to meet most requirements up to 45 kW with maximum output torque capacity of 10,000Nm.
Product Specification:
The Series C product adds to the growing family of new drives which has taken advantage of our many years of accumulated design expertise, together with the use of high quality materials and components. The end result is a series of speed reducing and geared motors offering high load carrying capacity, increased efficiency, quiet running and reliability.
- Unit Sizes: 03, 04, 05, 06, 07, 08, 09, 10
- Input Power: Up to 45kW (60HP)
- Output Torque: Up to 10,000Nm (88,500 lb.in)
- Gear Ratios: From 8:1 to 250:1 in a double unit and 60,000:1 in combined units
- Motor Sizes: IEC Frames from 63 to 225; NEMA Frames from 56 to 326
|
|
Right-angle geared motors are always applied where the mounting conditions or technical requirements call for a right-angle position. ABM worm gears are also available in a self-locking design, in elevators, for example, offering back-up safety to braking. Worm gears and helical worm geared motors are the classic solution of right-angle drives.
They offer the user the following advantages:
economy; due to the favourable cost/performance ratio
rugged and virtually maintenance-free
extremely quiet in operation
For applications requiring high efficiency, special ABM bevel gears are also available.
ABM Worm Gears
drive torques up to 300 Nm
reduction ratios up to 250 to 1
ABM Helical Worm Gear Motors
drive torques up to 4000 Nm
reduction ratios from 8 to 350 to 1
output speeds of 0.7 up to 330 rpm
ABM Bevel Gears
drive torques up to 1200 Nm
reduction ratios from 6 to 100 to 1
all other details available upon enquiry
|
|
| ... products without technical information |
| |
|
|
