|
|
General description
The ZL60301 is a very high-speed transceiver for parallel fiber applications. This transceiver performs E/O and O/E conversions for data transmission over multimode fiber ribbon. The transmit section converts parallel electrical input signals via a laser driver and a VCSEL array into parallel optical output signals at a wavelength of 850 nm. The receive section converts parallel optical input signals via a PIN photodiode array and a transimpedance and limiting amplifier, into electrical output signals.
The module is fitted with a pluggable industry-standard MegArray® BGA connector. This provides ease of assembly on the host board and enables provisioning of bandwidth on demand.
|
|
Manlight proposes a wide variety of Erbium (1,5µm) or Ytterbium (1µm) doped fiber amplifiers either using PM or non PM fiber.
Available in OEM module of different sizes depending on the power (with power up to 35dBm at 1,5µm and up to 43dBm at 1µm) as such as in benchtop 3U 1/2 19" (up to 40dBm at 1,5µm) or 3U 19" (up to 43dBm at 1µm), you will necessary find the product that you need for your application.
|
|
Main Features & Applications:
- 1529-1563 nm Bandwidth
- Fast Transient Gain Control Up to 12 dB
- Up to 12dB Mid-Stage Loss budget
- Compact Package
- Variable Gain
- Excellent Flatness APC, AGC, ACC modes
- For: Long-Haul and Ultra Long-Haul Applications
|
|
|
The EFA-series of benchtop EDFAs are repackagedversions of the high-performance optical amplifiers found in MPB's repeaterless-link telecom equipment. These wall-plug units include preamplifiers with high gain and near-quantum-limited noise figure, as well as power amplifier models with saturated output powers up to 23 dBm.
|
|
This system enables two-way half duplex digital links over a range of up to 6Km.
It is used as an asynchronous serial channel where the useful data rate ranges from 0.2 kBps to 50 kBps Manchester.
These systems offer 9 transmission channels
These modules (miniature daughter boards to be integrated) are available in 4 versions
* Monochannel 433MHz / 868MHz or 915MHz
* 8 channels 433MHz - 10mW
* 9 channels 868MHz
* 1/2/5 channels 868MHz - 500mW for long range applications
They are in accordance with the European Directive EN 300-220 / EN 301-489
The applications covered range from point to point transmissions, industrial remote controls, remote sensors to cordless local networks... in both industrial sectors of activity: robotics, remote control, and in general public or tertiary fields: access control, home automation...
For any information : http://www.adeunis-rf.com or +33 (0) 4 76 92 07 77
|
|
|
|
|
|
The Radiometrix UHX1 is a high-specification telemetry radio tranceiver.
The Narrow Band FM multi-channel VHF transceiver unit ideal for use in the new 169.4-169.475MHz European band. Squeezed into a compact, low profile package (67x30x12mm), it can provide a reliable data link capable of supporting rates of up to 5kbit/s or 1200 baud modem link over a range of more than 1km.
The dual frequency capability allows UHX1's transmitter section to be operated on one frequency while receiver frequency on another.
Features
-Conforms to ETSI EN 300 220-3 and EN 301 489-3
-High performance double superhet, 128 channel PLL synthesizer
-500mW RF power output: adjustable via serial command
-Data rates up to 5 kbps for standard module
-Usable range over 1km
-Feature-rich interface (RSSI, analogue and digital baseband)
-Incorporates a 1200baud modem
-Re-programmable via RS232 interface
-Low power requirements
Applications
- Heavy vehicle/machine remote controls
- Environmental monitoring equipment
- Automatic Meter Reading (AMR)
- Asset Tracking and Tracing
- Data logging systems
- Industrial telemetry/telecommand
- High-end security/fire alarms.
Technical specifications
Operating frequency: Any 2MHz segmnet in 140- 175MHz
128 channels controlled via RS232 interface
16 channels selected by parallel interface
Transmit power: : 500mW (+27dBm) nominal. Adjustable 1 - 500mW
Supply range: 5V regulated transmit, 3.1 - 15V receive
Current consumption: 330mA (at 500mW output) transmit, 25mA receive
Receiver sensitivity: -118dBm (for 12 dB SINAD)
|
|
Medium-Range RF Transceiver 868MHz
AMB8310
* 868 MHz Narrow Band transceiver
* LNA and PA for extended radio range
* Supports FSK, GFSK, ASK/OOK
* Configurable Bandwidth
* Data rates up to 57.6 kbps
* Output power up to 25 mW
* Low supply voltage
* Outstanding Rx sensitivity
* RF range (line-of-sight) up to 2 km
* EN 300 220 compliant
|
|
|
|
|
|
The RX3G is a PLL synthesiser based miniature PCB mounting UHF radio data receiver. With the matching TX3B-869-64 transmitters, RX3G allows the simple implementation of wireless data links at speeds up to 64kbps and distances up to 75 metres in-building or 300 metres over open ground.
* Designed to comply with harmonised radio standard EN 300 220-3
* Designed to comply with harmonised EMC standard EN 301 489-3
* Data rates up to 64kbps
* Usable range up to 300m
* Versions available on 868.3MHz, 869.5MHz and 869.85MHz
* Regulated and Unregulated versions available
* Fully screened
* Improved blocking performance
* Fast data settling time
Available for operation at 868.3MHz, 869.5MHz and 869.85MHz in Europe, the RX3G combines full screening with internal filtering to ensure EMC compliance by minimising spurious radiation and susceptibility.
The module suits one-to-one and multi-node wireless links in applications including car and building security, EPOS and inventory tracking, remote industrial process monitoring and computer networking. Because of the small size and low power requirements, the RX3G is ideal for use in portable, battery-powered wireless applications such as hand-held terminals.
|
|
Ready to use radio modules make life easier for the design engineer who has to develop a complete system containing a radio link. Radio modules are an interesting option for low to medium quantities up to several 1000 pcs per year.
Thanks to our SMD production plant we also have optimized parameters according to the customers need. We support you individually in integrating the modules successfully into the final application.
|
|
The TH71112 FSK/FM/ASK double-conversion superheterodyne receiver IC is designed for applications in the European 868 MHz industrial-scientific-medical (ISM) band, according to the EN 300 220 telecommunications standard. It can also be used for any other system with carrier frequencies ranging from 750 MHz to 990 MHz (e.g. for applications according to FCC part 15).
|
|
|
|
|
|
Code hopping receiver with up to 5 relay outputs
KDEC is designed to provide the user with a complete receiver interface for Radiometrix transmitters such as KTX2 and KFX2. No additional parts needed to implement a complete system suitable for applications requiring high security RF remote control.
Boards are pre-programmed to process messages from code-hopping transmitters and includes a high-performance UHF or VHF FSK receiver module.
The board has relays and screw terminations so that you can realise your own secure control application immediately.
There are momentary and latching modes and user-select KTX or KFX optimisation modes. Press the “Learn” button, initiate a transmission from your KFX2 or KTX module and the “Learn” indicator will flash to show that the KDEC will now act upon controls received from your transmitter.
Features
* Up to 5 relays to control mains powered devices rated up to 8A, 250VAC/30VDC
* Volt-free changeover contacts
* Learn button - remembers up to 16 different transmitters
* Remembers transmitters when switched off
* Visual indication of Learn function
* Visual indication of low supply voltage at the Transmitter
* Visual indication of activated relays
* Momentary or Latched outputs
* Basic antenna included - setup is simple Plug-and-Play
* Receiver module on-board
* Terminal block to connect external power supply
* SMA RF connection
* 9 – 16VDC supply
Applications
* RF interface for Security and Alarm systems
* Status reporting and monitoring secure systems
* Industrial controls
* HVAC controls
* Wireless door entry systems
* Simple On/Off switching
|
|
Radiofrequency keyfobs transmitters, AM & FM transmitter ideal for gate door opener, burglar alarms, personal security and remote controls.
FM (FSK/ ASK) Super-het low cost receiver of modulated digital data, working at 433.92 MHz frequency. High selectivity and sensibility obtained by SAW filter. Output voltage is low when no carrier is on air.
|
|
|
The RCR-315-EPR high performance RF receiver modules offer an extremely low cost solution for remote control type applications. The receivers are compatible with almost any ASK or OOK data transmitter and can receive legally transmitted signals from distances as far away as 600 feet. The receivers operate at 5V and draw only 4.5mA. The receiver is industrial temp spec -40C to 85C.
|
|
austriamicrosystems offers a high performance, low power UHF transmitter for wireless data transmission between 300 and 1000 MHz and a low power LF wake-up receiver supporting operation between 19 and 150 kHz.
|
|
Product Highlights:
* Antenna Style = Embedded Antenna
* Voice Application
* Antenna Type = World GSM
* 880 - 960 MHz Operating Frequency
* Mount = Tab
|
|
World smallest ceramic GPS chip antenna
11mm x 1,6mm x 1,6mm
also available for Bluetooth and W-Lan applications
|
|
The GPS market presents phenomenal opportunity. From its origins as a military technology, GPS has made a successful transition into consumer applications. And the number of consumer applications is growing rapidly.
Soon, GPS will be integrated and embedded into devices of all kinds and will be just another standard function. GPS receivers are small and portable. Their size, however does not limit their accuracy; not only can a GPS device determine your position anywhere in the world, it can be a source of other critical information. By FCC mandate, all handsets sold in the U.S. after October 2001 must have E-911 location capabilities. This single mandate is driving the market to include GPS-derived location information in wireless devices.
|
|
Features
Dimensions (l x w x h)
Weight (without cable)
Cable length
Mounting method
Connectors
Colour
VIC 100
Ø 90 x h 98.4
195g
No cable
Pole for 1.0 - 14 UNS-2A
N, TNC
White
|
|
Broadcom is developing solutions supporting the next generation of 3G and 4G high-speed mobile technologies. As part of the CellAirityTM Mobile Platform, Broadcom offers a family of HSDPA (High-Speed Downlink Packet Access), WCDMA (Wideband Code Division Multiple-Access), EDGE (Enhanced Data Rates for GSM Evolution), GPRS (General Packet Radio Services) and GSM (Global System for Mobile Communication) baseband processors for use in cellular handsets, PC cards and other wireless-enabled consumer electronics.
|
|
World's easiest GSM/GPRS Controller, embedded with a powerful PIC18F6722 Microchip processor, that offers built-in digital and analog I/O combined with GSM/GPRS connectivity in a compact form factor. Develop your application script simply and fast with the built-in libraries written in BASIC, PASCAL or C.
The Smart-Cell GSM Controller will reduce your Total Project Cost. It is specifically designed for reliable independent operation under most demanding field conditions.
Features:
- Microchip PIC18F6722 controller.
- 128KB User Flash Memory.
- 32kB of EEPROM Memory.
- 6 Protected Digital Inputs.
- 6 10-bit Analog Inputs.
- 4 SPDT Relay Outputs.
- Graphics Display Connector.
- 4x4 Keypads Connector.
- 2 RS232 serial communications.
- GSM/GPRS Cellular Modem.
- Normal and Sleep Mode operation.
- Battery Input for Back-up.
- Main voltage input indication.
- 2 LED's indicator.
- Ethernet Communication – Optional.
|
|
The Pix-Cell is a high performance, programmable Cellular Single Board Controller, that offers built-in digital and analog I/O combined with GSM/GPRS connectivity in a compact form factor. The heart of the GSM controller is a Microchip PIC18F6722 operating up to 32MHz which provides fast data processing. Design your applications with an integrated BASIC, PASCAL or C compiler designed specifically for Pix-Cell GSM Controller.
Features:
- Small Size: 95x60x15mm.
- Microchip PIC18F6722 controller at 32MHz.
- 128KB Flash for user memory application.
- 32kB of EEPROM Memory.
- 3 Protected Digital Inputs.
- 3 10-bit Analog Inputs.
- SPDT Relay Output.
- RS232 serial communication.
- GSM/GPRS Cellular Modem.
- Normal and Sleep Mode operation.
|
|
|
The A.H. Systems' set of H-Field Rods provide an accurate standard for magnetic field testing. The rods are available individually or in a set of four to cover the frequency range of 100 Hz to 30 MHz. For those situations when improved sensitivity is desired in magnetic field testing, the H-Field Rod is an effective alternative to traditional loop antennas. One amplifier pre-assembled to a metallic ground plane covers the entire frequency range and can be used with any or all of the H-Field Rod elements. Visist our website for more information. www. AHSystems.com
|
|
|
|
|
|
Key Cylinder Antenna
Features:
The Keylock Cylinder Antenna is designed to emit a RF signal and identify the customer's key in the ignition system. This antenna is to be placed in the Ignition Switch Lock Cylinder, inside the vehicle. Since it can be exposed to the final customer, the antenna finishing fulfils the highest quality requirements.
Overmoulded with PA66 (ABS optional) assuring the IP67 classification.
Output wires can be customized to customer's design. Inside the overmoulding, the inductance, resistance and quality factor can be customized to required values.
Characteristics:
* High stability in temperature (-40ºC up to +85ºC).
* LF transponder Emitter/Transmitter antenna.
* Ideally used in the Ignition Switch Key Cylinder.
* Free wire or special connectors can be provided.
* The enclosure will provide mounting features into the vehicle
and will ensure the mechanical robustness.
* Low tolerances in the resonance frequency LC.
* Anchor points for easy assembly can be provided.
* Custom L and R value under demand.
|
|
|
A.H. Systems' offers 13 Log Periodic Antennas. Each antenna is lightweight, compact, rugged and has been manufactured to ensure maximum gain, low VSWR and high power handling capabilities. Whether testing inside a shielded enclosure or outdoors, the antennas will display efficient performance characteristics through the broad frequency range of 80 MHz to 7GHz. Visit our website for more information. www.AHSystems.com
|
|
|
|
|
|
Precompliance test antenna series HyperLOG® 60xxx span 680MHz to 18GHz
The LogPer-antennas of the HyperLOG® 6000 series are based on an ultra-thin, GOLD-COATED high tech TEFLON base. Based on this high quality technology, the antenna-frequency-range could again be vastly extended . Now the maximum bandwidth available reaches from 680MHz up to as far as 18GHz. Its small physical antenna-size and low weight make this antenna predestined for mobile use. The 18GHz frequency range now also allows the detection of unusable signal sources like military radar, various satellite services, very high frequency bugs, etc.
Shipped including antenna, typical CALIBRATION DATA, detachable handle, tripod, and aluminum case.
- Optimal for usage with spectrum analysers for EMC measurement
- Top-quality high-tech TEFLON antenna support
- Excellent forward/backward ratio
- Freely alignable polarisation
- Excellent symmetry of radiation patterns
- Integrated 1/4" tripod socket
- Suitable for mobile use
- Made in Germany
- 10 years warranty
|
|
Our Log Periodic Antenna series are calibrated broadband antennae enabling the direct measurement of field strength over the full radiated emissions spectrum up to 3GHz.
The BTA-series of antennae are used for radiated emission and immunity testing. They come fully calibrated and capable or handling up to 1kW of power.
These antennae are used for emission testing for CE, FCC, Automotive standards, and Military standards.
|
|
A.H. Systems' designs, manufactures and delivers high performance Loop Antennas for a wide range of magnetic field testing. Whether used in a set to measure shielding effectiveness per MIL-STD 285 and NSA 65-6 or individually to satisfy specific requirements, the Loop Antenna is an efficient, low cost solution. www.AHSystems.com
|
|
The RF300 is a fully compliant, calibrated 2 meter loop antenna manufactured to comply with European product specific standard EN55015 section 7.2 and annex B (EN55015 is specific to luminaires).
The calibrated frequency range of the RF300 is 9 KHz to 30 MHz and each antenna is supplied with antenna factor data so that it can be used with any EMC receiver or spectrum analyser capable of antenna factor compensation.
|
|
Broadband antennas, compared to half wave dipoles, reduce test time because the technician did not have to stop the test to adjust the dipole antenna for each frequency. Most compliance standards now require the use of such antennas. The latest version of Mil-Std 461E states the used of broadband double ridge guide horn antenna as the antenna of choice for frequencies above 200 MHz.
A.H. Systems Double Ridge Guide Horns are broadband antennas that offer excellent performance over the frequency range of 170 MHz to 40 GHz. These Horn antennas are an excellent choice for both radiated immunity and emissions testing. Here are several double ridge guide horn antennas ideal for most compliance standards and/or general field measurements. Visit our website for more information. www.AHSystems.com
|
|
|
|
Radio, Microwave, Infra-red, Optical connections
