... The EOS pneumatic insulating glove tester is a tool recommended for inspecting insulating gloves used in electrical environments. It is used before and after each use, as well as for periodic visual inspections. This pneumatic tester checks the entire ...
PENTA ESP
... Phase tester for LV network Standards 1000V CAT IV - IP65 Use UNITAG is a unipolar detector designed to test the presence of phase on insulated or bare LV conductors. The level of detection is indicated by a LED bargraph and a beeping sound which ...
PENTA ESP
... The TT7415 detector checks the insulating quality of yours poles, rods and ropes. The tester does not only identify surface defects. Its capacitive principle of measurement allows to detect internal and external insulation faults. It provides in-depth ...
PENTA ESP
... 10V calibration reference for high level devices. Like the shunt calibration module for strain gaged extensometers, the VREF module is used to transfer Epsilon’s calibration to a customer’s electronics. • Calibration only requires these simple steps: • ...
Based on TSI's established model 8130, currently the world's most-used filter tester, model 8130A now offers higher sensitivity and resolution - up to 99.9999 percent efficiency has been produced with Emery oil at concentrations of 200 mg/m³. The new ...
TSI
... PRODUCT DETAILS TSI’s Automated Filter Testers have been used in quality control and manufacturing for more than 35 years. The model 8130A is used by the leading filter and filter media manufacturers, test laboratories, and government agencies around ...
TSI
The VelociCalc® Meter Model 9650 is used to measure HVAC system pressures and can be connected to pitot probes for performing duct traverses. It’s ergonomic design includes a probe holder and integrated magnets allowing for attachment to exposed ductwork ...
TSI
... Reliable PD testing on electrical equipment Our MPD 800 universal partial discharge (PD) measurement and analysis system represents the next generation of our widely-used and innovative MPD PD testing technology. Enhanced and newly-added hardware and ...
OMICRON electronics
... Ultra-high frequency partial discharge measurement and analysis system Our portable, easy-to-use UHF 800 system performs sensitive offline and online partial discharge (PD) measurement and analysis in the ultra-high frequency (UHF) range from 100 to ...
OMICRON electronics
MONCABLO is a customizable, permanently-installed system for the continuous on-line monitoring of partial discharge (PD) activity in the electrical insulation of high-voltage cable systems, including cable terminations and joints. Advanced diagnostic ...
OMICRON electronics
... Level and temperature measurement with a system lifetime up to 5 years. Internal SD card up to 1.000.000 readings. For use in ATEX Zone 1 -Self-sufficient level measurement system -Internal data memory for approx. 1.000.000 readings ...
... Mobile measurement system for discharge measurement in watercourses, such as rivers, streams and canals. The NivuFlow Stick is a mobile measurement system for discharge measurement in watercourses, such as rivers, streams and canals. Description ...
... NivuScope 2 measurement system for reliable separation layer detection and sludge level measurement mainly in primary and secondary clarifiers -Interface and sludge level detection independent of density -Indicates the current sludge level ...
... The reference probes, also called "dummy probes", are resistance dividers. Each probe simulates a given length very accurately. Reference probes are connected to the instrument instead of standard probes for checking or calibrating electronic devices ...
TESA Technology
... Suction support with articulated arm SPECIFICATIONS Material - Arm: light alloy Base: metal Dimensions - Base: Ø 88 x 28 mm Function(s) - Suction controlled by lever switch Fine adjustment Included in delivery ...
TESA Technology
... Magnetic supports with articulated arm SPECIFICATIONS Material - Arm: light alloy Base: metal Function(s) - With switch to disengage the magnet Fine adjustment Included in delivery - Articulated arm ...
TESA Technology
The MR06-200 wire crimp pull sensor is a hand-operated solution for measuring wire crimp pull-off forces. The ergonomic handles and convenient tensioning mechanism make field measurements a breeze for applications up to 200 lbF (1,000 N). Squeeze the ...
Mark-10
... Series TSTM-DC advanced motorized torque test stands are designed for a wide variety of applications, including closure torque testing, fastener torque testing, and more. Two torque capacities are available, 100 lbFin (11.5 Nm) and 200 lbFin (22 Nm). The ...
Mark-10
Measure wire crimp pull forces accurately and efficiently with the portable and customizable WT-205 tester. Easily apply up to 200 lbF (1,000 N) of force via an ergonomic lever. The tester's standard adjustable terminal fixture contains multiple slots ...
Mark-10
... Polarimeter – Quartz Plate Calibration Standards Rudolph Research endeavors to adhere to the highest know calibration standards in the laboratory instrument industry. To view our full NVLAP certificate and Scope of Accreditation, please visit our Quality ...
The DSA100HP is our high-quality solution for the precise measurement of contact angle and surface tension and interfacial tension under high pressures and temperatures, primarily for tertiary oil recovery. The DSA100HP combines our Drop Shape Analyzer ...
... The Alluris FMT-W40 motorised wire-terminal pull-tester is designed for crimped wire terminal testing according to IPC/WHMA-A-620, UL 486, ASTM B913, USCAR 21, EN 2591-417, MIL-STD 202-H, NASA 8739-4 and many more relevant standards. Two versions of ...
Mecmesin
... The Alluris FMT-W30 manual wire-terminal pull tester is designed for crimped wire terminal testing where budgets are limited and it has been decided to overlook the recommendations in test standards to test at a constant pull rate. Two versions are ...
Mecmesin
... The Mecmesin MEC-FD Falling Dart Impact Tester range is designed to measure the impact resistance or toughness of plastic films in compliance with ASTM D1709 and ISO 7765-1 free-falling dart Methods A and B. The machine is available in 3 different ...
Mecmesin
... PTBA 211E ampoule breakpoint tester to control the quality during production of empty ampoules The PTBA 211E ampoule breakpoint tester is designed and manufactured in compliance to the DIN EN ISO standard. According to this standard the break point ...
Pharma Test Apparatebau AG
... Tapped Density and Apparent Density Testing Instrument The PT-TD300 is used to test the tapped (or “tamped”) density and apparent density of powders, granules, pigments and similar products in compliance with the current USP methods 1 and methods 2 ...
Pharma Test Apparatebau AG
The SPT-6 Suppository Penetration Test assembly is used to determine the softening time of six samples at the same time. It is connected to a Pharma Test PTZ AUTO or PTZ-S tablet disintegration test instrument. The SPT-6 assembly can also be immersed ...
Pharma Test Apparatebau AG
Passi Test Plus is a tool designed to assess the real quality of stainless steel. It consists of a “probe pen”, which contains the electrochemical solution, and an external storage unit. By pressing the probe pen on the surface, Passi Test Plus measures ...
Passi Test is a tool designed for those who need to know exactly the real quality of the stainless steel. It consists of a “probe pen” – which will be put on the superface to be tested – containing the electrochemical system and a reading external unity. ...
... DK/S – Block Gauges - Spring Actuation •2, 5 and 10 mm measuring ranges •Accuracy better than 1 µm •Resolution better than 0.01 µm •Repeatability better than 0.25 µm •Tool holder and tip options •Spring actuation •IP65 sealing Solartron’s ...
SOLARTRON METROLOGY
... DK/P – Block Gauges - Pneumatic Actuation •2, 5 or 10 mm measuring ranges •Accuracy better than 1 um •Resolution better than 0.01 µm •Repeatability better than 0.25 µm •Tool holder and tip options •Pneumatic actuation •IP65 sealing Solartron’s ...
SOLARTRON METROLOGY
... DU/S Parallel Flexure Spring Actuation •0.5 1 and 2 mm measurement ranges •Accuracy better than 0.1 µm •Resolution better than 0.01 µm •Repeatability better than 0.05 µm •Spring actuation •IP65 sealing •Removable leaves for ease of repair ...
SOLARTRON METROLOGY
Siviko ACT 150 is an innovative automated cable tester that offers reliable and convenient automated solution for cable manufacturers and distributors that want to ensure the quality of their products by running in-house electric tests for active resistance, ...
... Overview
Siviko ACT 15 is an automated cable test system designed for non-destructive resistance and AC high-voltage testing of multi-conductor cables. It automates conductor switching, data acquisition, safety monitoring and report generation, ...
DRC SRL.it
... Overview
- On-line, continuous, real-time, contactless measurement on a conveyor belt.
- Designed to improve yield and quality control in industrial processes; reduces energy and raw material use — quick ROI.
Measured ...
Cefem Group
... On line Continuously In real time Contactless On a conveyor belt Ideal measurement device for improving yield and quality control for industries. Advantages : Simultaneous measurement of 2 constituents Reliable and precise infrared technology On line ...
Cefem Group
... DL lasers positioning are designed to generate a bright red line from 2 to over 12 meters. This range is the result of over 30 years of experience in positioning laser. Its design gives it great strength and better resistance to vibration machines. All ...
Cefem Group
The 7006 is a single function low-cost pocket sized simulator, designed for test and calibration of process loops. It is simple operation and engineers will be able to pick up the unit and get to work immediately. Just select 4 to 20 mA or 10 V loop, ...
Time Electronics
... The 7007 LoopMate 2 is a dedicated loop signal indicator (RxSim) with an in-built 24 V loop drive supply (TxTest). The operator can select the loop type, and also the type of units, either direct (mA) or % of span display. The loop signal is shown on ...
Time Electronics
The CBP-PRES1 CalBench is a package that provides users with the capabilities to perform rapid calibration of pressure instrumentation. It is an ideal solution for instrument workshops that require a high performance workstation as the platform for calibration ...
Time Electronics
... Product overview
The Delta ClubStar 12-FB4 is a professional diode laser projector for club laser shows and indoor/outdoor events. Its compact design facilitates installation for fixed venues, touring or rental applications. The precision optical ...
Delta Lasers Technology Ltd
... Overview
The ClubStar series is designed for club laser shows and live events. Its compact footprint simplifies installation while the precision optical system produces a low-divergence beam with vivid colors and balanced whites. Delta ClubStar ...
Delta Lasers Technology Ltd
... Product overview
Compact laser projector designed for club and small venue laser shows. Precision optical system with low beam divergence ensures bright RGB colors and accurate white balance. Available in outputs from 3W up to 4W in the same ...
Delta Lasers Technology Ltd
... Product Introduction
This instrument is developed, designed and manufactured on the electrolytic test principle in accordance with GB/T 21529, ISO 15106-3 and related standards. It measures the water vapor transmission rate (WVTR) of samples ...
Guangzhou Biaoji Packaging Equipment Co., Ltd.
... Product introduction
W203 2.0 is developed on the electrolytic test principle and is designed and manufactured in accordance with GB/T 21529, ISO 15106-3 and other international standards. It measures water vapor transmission rate (WVTR) of ...
Guangzhou Biaoji Packaging Equipment Co., Ltd.
... Application
W413 2.0 water vapor permeability tester is designed to measure the water vapor transmission rate (WVTR) of films and sheet materials under controlled temperature and humidity conditions.
Applied to
- Plastic
Guangzhou Biaoji Packaging Equipment Co., Ltd.
... Overview
- Single unit for both in-phase and different-phase checks on low-voltage three-phase systems.
Key functions
- Live-part display function: differentiates charging status (voltage to ground ≥ 80
Hasegawa Electric Co., Ltd.
... FRP is used for the insulating stick. It is lightweight and outstanding in operability . Working voltage is wider than HPI-S20. ...
Hasegawa Electric Co., Ltd.
... Easy to use with Wireless pair Multi-functional phase tester Voltage Detection by single detector use, Phase check, Phase sequence check with pair detector use. ...
Hasegawa Electric Co., Ltd.
... BETA BASIS WEIGHT MEASUREMENT FOR THE PRODUCTION OF LITHIUM-ION BATTERIES The basis weight measuring device is a high-precision, non-contact online measuring system for continuous quality monitoring in electrode production. It reliably measures the ...
... X-RAY BASIS WEIGHT MEASUREMENT FOR THE PRODUCTION OF LITHIUM-ION BATTERIES The X-Ray basis weight measuring device is a high-precision, non-contact online measuring system for continuous quality monitoring in electrode production. It reliably measures ...
... PRECISE THICKNESS MEASUREMENT FOR ANODE / CATHODE COATING The laser-based thickness measurement system is a non-contact, online solution for continuous monitoring of coating thickness on anodes and cathodes. It reliably measures layer thickness across ...
... Portable Switchgear Test System Flexible and compact test system for the testing of medium-, high- and extra-high voltage switchgear with a plus in control and performance. 1. Wider range of applications due to more control outputs and more ...
KoCoS Messtechnik AG
... Automated Wafer Edge Profiler WATOM 200/300mm Wafer Edge Measurement - pinpoint precise The use of smaller and smaller patterns in the semiconductor industry calls for increasingly advanced materials of extremely high quality. In response to the ...
KoCoS Messtechnik AG
... LOTOS - 3D measurement and inspection LOTOS automatic measuring systems can measure the full outer and inner contours or individual areas of any measurement object quickly and precisely, irrespective of the shape, and test them for defects. The three-dimensional, ...
KoCoS Messtechnik AG
... Art.# M-28.10 Strato Line 3D Articulated Gauging Arm Fine adjustment, articulated arm 280 mm, switch magent Consisting of: •Fine adjustment Ø 8 mm (Art.# 5.320) •Articulated arm 280 mm (Art.# 4.200) •Switch magnet approx. 800N (Art.# 5.079) ...
Fisso
... Art.# AP28.10 Strato µ-Line 3D Articulated Gauging Arm Precision fine adjustment, articulated arm 287 mm, switch magnet Consisting of: •Precision fine adjustment Ø 8 mm (Art.# 5.350) •Articulated arm 287 mm (Art.# 4.700) •Switch magnet approx. 800N (Art.# ...
Fisso
... Art.# AP13.10 Strato µ-Line 3D Articulated Gauging Arm Precision fine adjustment, articulated arm 130 mm, switch magnet Consisting of: •Precision fine adjustment Ø 8 mm (Art.# 5.350) •Articulated arm 130 mm (Art.# 4.500) •Switch magnet approx. 600N ...
Fisso
... Overview
BlueAngle is a gyroscope-based Bluetooth angle sensor designed to attach easily to a rotor via its magnetic base. While rotating with the rotor, BlueAngle measures the rotating angle and wirelessly transmits readings to an ...
... Insulation Testers RCD Testers Loop Testers Wiring Check Included calibration checksheet for your instrument Designed with low cost, portability and ease of use in mind, the 2080 provides on or off site verification of RCD testers, Loop testers, ...
... Standalone battery operation 230V and 110V appliance testing Visual pass/fail test indicator Bond current @ 25A/10A/100mA Insulation resistance @ 500V Leakage current @ 230V Re-defining rapid safety testing, the Transmille 6080A battery powered ...
... Standalone battery operation Visual pass/fail test indicator Bond current @ 25A / 10A / 100mA Insulation resistance @ 500V Leakage Current @ 230V Re-defining rapid safety testing, the Transmille 5080 battery powered portable appliance tester provides ...