Testers

... • Operating Temperature: 0–45℃ • Operating Humidity: <75% RH • Dimensions: 460×280×320 mm The HZJQ-X1 Transformer Oil BDV Tester is designed for testing the breakdown voltage of insulating oil, widely used in power systems, railways, ...

... • Multiple output frequencies: 0.1Hz, 0.05Hz, 0.02Hz, 0.01Hz • High load capacity: up to 5.5 µF at 0.01 Hz • Measurement accuracy: ±3% • Positive/negative peak voltage error: ≤3% ± 3kV • Waveform distortion: ≤5% • Wide operating conditions: -10℃ to +40℃, ...

... • Multiple output frequencies: 0.1Hz, 0.05Hz, 0.02Hz, 0.01Hz • High load capacity: up to 5.5 µF at 0.01 Hz • Measurement accuracy: ±3% • Positive/negative peak voltage error: ≤3% ± 3kV • Waveform distortion: ≤5% • Wide operating conditions: -10℃ to +40℃, ...

... TL-CF2 is a Flame Detector tester for UV/IR and IR3 Model to verify its response within a short distance. • Approval for Explosion-Proof • Portable device • Specialized for Rezontech UV/IR and IR3 type of flame detector ​• Suitable ...

... TL-205 is a UV/IR Flame Detector tester to verify response of UV/IR type of Flame Detector within a short distance.  ​• Portable device ​• Specialized for Rezontech UV/IR type of flame detector  ​• Suitable for hazardous areas such ...

... TL-3000 is a IR3 Flame Detector tester for RFD-3000, RFD-3000X Model to verify its response within a short distance.  • Portable device • Specialized for RFD-3000, RFD-3000X Models • Suitable for hazardous areas such as gas stations, ...

... Vibration tester is used for discovering the early faults, simulating the actual working condition and the structure strength test, the product application is wide, the application width is obvious, the test effect is remarkable and reliable. It ...

... Overview
Next-generation tester platform for wide bandgap power products. Designed for high-throughput production with rotary turret and conveyor handlers, it measures static parameters, dynamic switching performance, thermal ...

... Short description
The high-voltage wafer test solution for SiC and Si devices. M2 Wafer Edition integrates a 10 kV DC generator to enable early-stage wafer screening of high-voltage power die before singulation, reducing packaging of defective ...

... Product introduction
The UHV-1201 six-phase relay protection tester is a compact microcomputer-based test instrument designed to DL/T 624-2023. It provides flexible combinations of up to 6-phase voltage and 6-phase current outputs ...

The UHV-2000A is a dual-channel partial discharge (PD) analyzer for detection and analysis of PD in high-voltage equipment such as cables, insulators, bushings and transformers. It provides 2D and 3D visualization of PD activity, supports data and image ...

... Product overview
The UHVQW Series inflatable no-partial-discharge test transformer is developed for insulation withstand and partial-discharge measurement of high-voltage, large-capacity power equipment such as GIS, GIL and power transformers. ...

... ACT-1000N is automatic crimp tester with 1000N capacity. It performs crimp test automatically from testing to storing the data by simply pressing start button which enhances the testing efficiency. Feature • - Perfect solution for ...

... Wire crimp tester LH-500N is a lever-operated manual test stand including wire/terminal grips. With a force gauge, it offers a testing system to perform wire crimp test. Features It offers a simple and affordable ...

The PCE-ERT 10 is a handy measuring instrument, which allows fast and easy determination of the earth resistance. The earthing device determines the earth resistance with three-wire technology in three measuring ranges up to 2000 Ω. By means of a rotary ...

... electrical tester PCE-CBA 10 is a car battery tester and allows fast and easy testing of 12V voltage starting batteries. The electrical tester has various test modes to determine the condition of the ...

... PCE-VDV 10 is a portable network tester for diagnosing faults in network and coaxial cables. It is a two-part system with a main unit and a remote unit that enables testing of permanently installed cabling. The tester ...

... Packaging Clamping Force Testing Machine HD-A534 Minimum 1 SET Delivery 15 days after order. Country China BrandName HD-534 Package Each set protected with resin fiber and PP film, then put into Strong wooden case with operation manual ...

... Product Description
Porous Ceramic Air Permeability tester meets the requirements of GB/T1968. It quantifies the volume of air (m³) passing through a porous ceramic specimen of 10 mm thickness and 1.2 m² area under laminar flow ...

... Product Description
Model 60098-HD is a laboratory-grade wear-resistance tester designed for unglazed ceramic tiles and mosaics. The instrument performs standardized abrasive wear tests in compliance with GB/T3810.6—2016 and ...

... A compact handheld ultrasonic pulse velocity and pulse echo tester is designed for ultrasonic thickness measurements and flaw detection of concrete and reinforced concrete constructions and rocks. The flaw detector represents an compact ...

... structures with up to 2 meters thru-transmission capability. A compact, ergonomic and easy to handheld ultrasonic pulse velocity tester for quality assessment of concrete compliant with valid international standards. The instrument ...

... A compact, ergonomic and handheld ultrasonic pulse velocity tester for concrete inspection. The device is made of light-weight shockproof plastic and has two built-in transducers with dry-point-contact with fixed base (150 mm). Wear ...

... Application : Insulated screwdriver for LV live working at low voltage. Phase-indicating screwdriver with LED indicator Features : In accordance with IEC 60900 standard. Maximum operating voltages : 1 000 V AC - 1 500 V DC. ...

... Application: Measurement of earth resistance. Highlight phase position and check the presence of earthing connection. Controls continuity of metal masses (buzzer). Features: Quick reading of conformity due to bicolor LCD ...

... The CATEX testers enable you to perform the following checks: Presence of voltage at the terminals of a socket. Integrity of the earth circuit. Correct polarity. The position of the phase and the neutral is indicated. ...

... Overview
The S 6600H, S 6600U and KT 6680U are universal safety testers designed for comprehensive electrical safety testing in laboratories, workshops and production environments. The S 6600H and S 6600U are modern desktop ...

... safety-related tests. The P 6600H tester is equipped with a country-specific socket on the front panel for connecting the DUT. This socket enables a direct connection to the DUT. In contrast, the P 6600U tester has ...

... The IS 6600H and IS 6680H insulation testers are outstanding solutions for carrying out insulation measurements and combine advanced technology with sophisticated design. The IS 6600H is a modern desktop device, while the IS 6680H is ...

... Overview
The Qscratch 20 GO is a semi-automatic macro/micro scratch tester designed for standardized quality control of coatings and surfaces. It supports single measurements with progressive or constant load and provides traceable, ...

... Introduction
The Qscratch 20 is a fully automatic macro/micro scratch tester for quality control of coatings, functional surfaces and components subject to critical loads. The system combines controlled force application, precise ...

Product overview TOHMY® measures the impedance of grounding systems and automatically transmits measurement data remotely. Information is accessible through a mobile app or a centralized web platform and is recorded and monitored in real time. ...

... system. The INGESCO® Advanced ESE Tester permits the execution of an advanced functional analysis to detect any abnormality in the lightning rod behaviour. Recommendations • The INGESCO® Advanced ESE Tester requires ...

... State-of-the-art of Uniformity & Polarization Tester according to Standards. Smart_ Tester allows a complete Polarization Axis and Transmittance Uniformity Check for SunLenses, SunGlasses, Masks and SkiGoggles according ...

... HW/SW Device for Smart_ Tester for Photochromic Lens Activation Smart_PhotoChromic_Device is a HW/SW Solution designed for use with Smart_ Tester. Thanks to this Accessory is possible the Photochromic Lens Activation ...

... Automatic Uniformity Tester according to ISO 12312-1, GB 39552.1, ANSI Z80.3, ISO 16321-1, EN 174 & ISO 18527-1 Easy_ Tester_Pro is the Worldwide Optical Market Standard Device that performs a complete and automatic ...

... tool which can be operated in the field by any personnel, expert or not.

Digital Optical Oil Tester:

The GESERCO Rapid Optical Oil Tester has a last generation infra-red sensor which combines measurement ...

...

The GESERCO FlashTest apparatus is a manual Pensky-Martens type closed-cup flash point tester.

Designed for fast, simple and cost-effective determination of flash points in petroleum products, from the

... The GESERCO FlashTest™ apparatus is a manual Cleveland type open cup flash point tester. Designed for fast, simple and cost-effective determination of flash points in all petroleum products (above 79°C and bellow 400°C) except fuel oils. The ...

With unmatched precision, speed, and versatility ERAVAP is the instrument of choice for vapor pressure testing of e.g. gasoline, crude oil, LPG, solvents, fragrances, or aqueous solutions in full compliance with the latest international standards. With ...

... ERAFLASH X is the future-proof replacement for ASTM D93 Pensky-Martens testers. Tailored for the petroleum industry all kinds of liquids can be tested over the wide temperature range of 18 °C to 370 °C using only 2 mL of sample. The full ...

ERAVAP FOR CRUDE OIL is the leading solution for high precision vapor pressure and density (ASTM D4052) testing of live and dead crude oils according to ASTM D6377, IP481 and GOST 52340. Its unique cell design allows high shaking speeds ensuring unrivaled ...

... the Elcometer 510 Pull-Off Adhesion Tester ensures smooth and continuous pressure application for consistent and repeatable results. Whilst the rate of pull is controlled manually for most pull-off adhesion testers, ...

... 506 adhesion testers ensures that a uniform force can be easily applied throughout the range by smoothly rotating the gauge's crank handle, ensuring repeatable adhesion results to an accuracy of ±1%. The Elcometer 506 adhesion tester's ...

... The Elcometer 508 Push Off Adhesion Tester is an extremely versatile Type III* adhesion gauge which can be used to test adhesion strength of coatings. Powerful • Suitable for use on flat, concave & convex surfaces • Rugged ...

... 600 V (three-phase)

Technical specifications

• Model: HPL-200
• Application: Low-voltage phase tester for three-phase systems
• Voltage measurement range: 80–600 V (three-phase)
• Detection: Live-part

... Easy to use with Wireless pair Multi-functional phase tester Voltage Detection by single detector use, Phase check, Phase sequence check with pair detector use. ...

... FRP is used for the insulating stick. It is lightweight and outstanding in operability . Working voltage is wider than HPI-S20. ...

... Overview
PW366Ai (12×20A, 4×300V, 8 fiber optic ports) is a next-generation protection relay test set designed for both conventional and IEC61850-based digital relay testing. It provides high-power, high-accuracy analog outputs, extensive binary ...

PW-VP50 CT Polarity checker is the favorable meter which can be used for field CT and transformer polarity test in power plants, substations and any other application which may need to check the polarity. There are 2 units included in PW-VP50. One master ...

... FT3000 HVDC Power Filter Characteristic Tester has the functions of automatic sweep harmonic signal output, A-F and P-F characteristic measurement/display etc. It can perform HVDC Power Filter Testing and is mainly used in AC filter of ...

The 7006 is a single function low-cost pocket sized simulator, designed for test and calibration of process loops. It is simple operation and engineers will be able to pick up the unit and get to work immediately. Just select 4 to 20 mA or 10 V loop, ...

... The 7007 LoopMate 2 is a dedicated loop signal indicator (RxSim) with an in-built 24 V loop drive supply (TxTest). The operator can select the loop type, and also the type of units, either direct (mA) or % of span display. The loop signal is shown on ...

... Product Overview

• Pressure Cycle Testing up to 6,000 bar. A pressure cycle test simulates the service life of a component using a sine (wave) or trapezoidal (square) waveform.
• Suitable for testing metal and plastic components, including

... Insulation Testers RCD Testers Loop Testers Wiring Check Included calibration checksheet for your instrument Designed with low cost, portability and ease of use in mind, the 2080 provides on or ...

... 500V Leakage current @ 230V Re-defining rapid safety testing, the Transmille 6080A battery powered portable appliance tester provides simple, fast and safe PAT testing for both independent contractors and in house safety testing. ...

... @ 500V Leakage Current @ 230V Re-defining rapid safety testing, the Transmille 5080 battery powered portable appliance tester provides simple, fast and safe PAT testing for both independent contractors and in house safety testing. ...

... analyzed. In addition, the PROFIBUS Tester 5 supports the export of test results for advanced analysis. Overview Test PROFIBUS Cable, Signals, and Data, All-In-One Handheld Tester • - Combination of PROFIBUS signal ...

... The PST 100 Spark Tester provides a quick and cost effective method of inspection on thick coatings and linings. Coating thicknesses of between 3 and 30mm can be tested. It can be widely used for testing butt-welded and overlap joints ...

... The CRIT 100 controls the charge of static electricity and the insulation of operators and equipment before entering a pyrotechnical area, where user’s safety is at stake. Dual detection of resistance thresholds: • Maximum value to prevent electrostatics ...

... EASYLAN is a powerful LAN tester for certification of copper cables, optical cables and networks up to 30 MHz. It stores up to 1,700 tests managed by sites and enables users to issue comprehensive certification reports using EASYSOFT ...

... The CETA flow testers can be used to measure volume flow rates using compressed air as test medium. The measuring method uses the fact that the pressure difference between two measuring points in a laminar flow is directly proportional ...

... send data from the field (download and upload) - Point to point testing for fixed appliances *Product Update: Apollo testers with firmware version 5 and above are no longer compatible with the standard Elite model printer. Only the ...

... making it an efficient and versatile tester for PV systems. 999 datasets can be stored on the instrument and once downloaded to the SolarCert software comparison to the standard test conditions can be made. The tester ...

... The PrimeTest 50 portable appliance tester is battery powered and handheld to allow for fast and efficient testing with clear PASS/FAIL indication. A simple range of tests are selected at the push of a button to test earthed equipment, ...

... Multifunctional Installation Tester Installation tester for standards-compliant testing in electrical systems and installations in accordance with IEC 60364-6 (DIN VDE 0100-600), DIN EN 50110-1 (DIN VDE 0105-100), ...

... The new installation testers included in the PROFITEST MF series are ideally matched to the electrician’s requirements and are specially designed for the implementation of electrical tests in installations and systems – day in, day out. The ...

... Non-contact voltage tester with slimline, insulated measuring sensor for fast, contactless voltage indication Thanks to its slender, insulated measuring sensor, the METRALINE VT SENSE facilitates fast, non-contact voltage indication. ...

... Tester used to verify the charge status of the 6/12V batteries (WET, GEL,AGM, PbCa). It is very compact, practical, easy to use and allows operations without disconnecting the battery from the vehicle; this is an enormous time saver during ...

... Intelligent digital tester for checking the charge status of a battery and the correct functioning of the vehicle's starting system and battery charging system (alternator). Extremely compact size, practical and easy to use. ...

... battery manufacturer (EN, IEC, DIN, SAE, CA -MCA) to which different starting current ranges correspond. Intelligent digital tester used to verify the charge status and start current capacity of 12V batteries (WET,GEL,AGM,PbCa). It is ...

... Overview
ATEQ introduces the MF520, a differential micro-flow tester combining fast cycle times with precise leak measurement using differential pressure-drop and stable flow measurement.

Applications

• Leak

... Overview
After more than 50 years and 300,000 testers installed worldwide, ATEQ presents the D6 CLASS flow tester: new electronic module, new measurement module, new interface and new accessories designed to ...

... Product overview
The D26 SPEED is a compact high-speed flow tester designed for automatic and semi-automatic test machines. With a throughput up to 240 parts/min, it provides continuous flow measurement, fast inline integration ...

... InteliSENS® HF Series High-Frequency Spark Testers are designed to meet International Standards for wire insulation testing. UL1581, EN50356, IEC62230. High-Frequency Spark testers enable greatly increased production ...

... InteliSENS® ST-AC series mains frequency spark testers meet the international standards stipulated for wire insulation testing UL1581, UL2556 and EC62230. The Proton Products mains frequency AC Spark Testers are designed ...

... Sparktester for insulation testing on cables in insulating and sheathing lines Properties Testing with sinusoidal alternating voltage and mains frequency or low frequency Bare patch and pinhole detection Electrodes for product diameters up to 250 ...

... • Fast and safe density testing of welding seams, containers or manufactured coatings • Non-contact spark generation • Maintenance free • Integrated stabilisation switch • Independent operation in case of mains voltage fluctuations • marking: CE Order ...

The weld test die can be used to punch out test pieces up to a thickness of 6mm. The test pieces are dimensioned in accordance with DVS [German welding association] 2225 Part 4.

... pneumatic insulating glove tester is a tool recommended for inspecting insulating gloves used in electrical environments. It is used before and after each use, as well as for periodic visual inspections. This pneumatic tester ...

... The TT7415 detector checks the insulating quality of yours poles, rods and ropes. The tester does not only identify surface defects. Its capacitive principle of measurement allows to detect internal and external insulation faults. It ...

... Phase tester for LV network Standards 1000V CAT IV - IP65 Use UNITAG is a unipolar detector designed to test the presence of phase on insulated or bare LV conductors. The level of detection is indicated by a LED bargraph and ...

... Based on TSI's established model 8130, currently the world's most-used filter tester, model 8130A now offers higher sensitivity and resolution - up to 99.9999 percent efficiency has been produced with Emery oil at concentrations of 200 ...

... PRODUCT DETAILS TSI’s Automated Filter Testers have been used in quality control and manufacturing for more than 35 years. The model 8130A is used by the leading filter and filter media manufacturers, test laboratories, and government ...

... equipment such as anesthesia gas delivery machines, insufflators and oxygen concentrators. Its compact size makes this ventilator tester ideal for use in field service, biomedical shops, and manufacturing. The fast response and bi-directional ...

... A powerful combination The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate ...

... Resonance circuit for GIS testing High-voltage testing with GIS resonance circuit For HV testing OMICRON’s CPC 100 + CP RC are directly connected to the voltage transformer of the GIS, forming a resonance circuit. This reinforced “Power VT” is an ...

... Handheld polarity checker The CPOL2 can be used as an accessory for several OMICRON test sets: • CMC, COMPANO 100, CPC 100 and CT Analyzer It offers the following functionalities and features: • Polarity check of current transformers and voltage ...

... The HVA28 and HVA28TD are truly compact and portable VLF test sets which determine the condition of medium voltage cables. HVA28TD device includes integrated Tan Delta diagnostics capabilities, in comparison to HVA28 device, which can be with the TD ...

... diagnostics unit enables a straightforward condition assessment of the cable system. The new HVA68TD is more than just a VLF tester. In addition to VLF testing & Tan Delta diagnostics capability, it allows to pre-locate arcs in the ...

... The HVA34-1 and HVA34TD-1 are truly compact and portable VLF test sets which determine the condition of medium voltage cables. HVA34TD-1 device includes integrated Tan Delta diagnostics capabilities and features TD leakage current correction (guard terminal), ...

... THE AUTOMATIC INCLINED PLANE TESTER FOR STATIC FRICTION COEFFICIENT DETERMINATION Sofraser’s FTIP, with its motorized, inclined platen, uses the simplest technology for the dynamic coefficient calculation of slip resistance measurement. The ...

The MR06-200 wire crimp pull sensor is a hand-operated solution for measuring wire crimp pull-off forces. The ergonomic handles and convenient tensioning mechanism make field measurements a breeze for applications up to 200 lbF (1,000 N). Squeeze the ...

... pull forces accurately and efficiently with the portable and customizable WT-205 tester. Easily apply up to 200 lbF (1,000 N) of force via an ergonomic lever. The tester's standard adjustable terminal fixture contains ...

... wire crimp pull forces up to 200 lbF [1 kN] accurately and efficiently with the WT-205M motorized pull tester. Portable and customizable, the tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements ...

... The Alluris FMT-W40 motorised wire-terminal pull- tester is designed for crimped wire terminal testing according to IPC/WHMA-A-620, UL 486, ASTM B913, USCAR 21, EN 2591-417, MIL-STD 202-H, NASA 8739-4 and many more relevant standards. Two ...

... operation of the FMT-W30 pull tester makes it very easy to use, and ideal as a portable device in situations where a constant pull speed is deemed not essential, or where mains power is not available to run a motorised pull tester. The ...

... The Mecmesin MEC-FD Falling Dart Impact Tester range is designed to measure the impact resistance or toughness of plastic films in compliance with ASTM D1709 and ISO 7765-1 free-falling dart Methods A and B. The machine is available ...