Other clamping elements

Clamping force: 40 N

Pneumatic Pin Holding Clamp is an automated quick fastener with air. Ideal for frequent changeover of tooling, plate and fixture in machinery. Pneumatic Pin Holding Clamp reduces your setup time in semiconductor manufacturing/food processing/pharmaceutical ...

Clamping force: 1,100 N - 3,500 N

Manual swing clamp for quick workpiece setups without using tools. The clamp arm swings into position over the workpiece and clamps straight down just by turning the handle. Spiral cam provides quick clamping with maximum 3500N. Ideal ...

Clamping force: 150 N - 650 N

SPRING SWING CLAMPS Handle clicks at the clamping endpoint. -Feature- ・Turn the handle after the arm swings into position, the cam shaft rotates along the guide pin to push down the arm. The clamping spindle contacts the workpiece ...

Renishaw Equator™ fixturing enables quick and easy fixture set-ups to be created regardless of the size, geometry or material of the part. Modular and custom fixturing for your Equator™ gauging system: Renishaw Equator™ fixtures ...

The Renishaw CMM fixtures range includes a wide choice of standard size base plates and an extensive selection of components with M4, M6 or M8 threaded fittings. Whether you are inspecting parts for aerospace, automotive, electronics, ...

Renishaw's vision fixtures and acrylic base plates allow for back lighting and a clear, clean look at the part from your vision system and multi-sensor machines. Vision fixtures: Renishaw's vision fixtures offer two unique fixturing ...

Clamping elements GN 826 are normally used in connection with control knobs and smaller handwheels. Spindles can so be clamped gently and easily and without much construction and installation effort. The clamping wedge stiffens the spindle, ...

With side clamps GN 9190, workpieces are clamped with a pivoted clamping jaw. The clamping force acts laterally and from above to pull down on the workpiece and clamp it against fixed stops and the supporting surface. The clamping ...

Clamping force: 10, 5 kN

Down-thrust clamps GN 9192 are compact clamping elements for quick and secure clamping in tool and fixture construction. Rotating and tightening the clamping screw or the adjustable hand lever moves the clamping arm downwards to clamp ...

Advantages: - Very high retaining forces of 30–49 kN. - Low height. - Simple element assembly. - Enables very fast, simple clamping. - Infinitely adjustable height and length. - Use in 14-28 mm T-slots or M12, M16, M20 grid systems. - ...

Clamping force: 2 kN - 38 kN

Material: Carbon steel, tempered. Version: Form A-C: black oxidised. Shaft diameter ground. Form D: black oxidised.Note:The stated clamping forces (F max.) and tightening torques are valid within the stated clamping ranges (H5). Advantages: Compact ...

Material: Steel. Housing thermoplastic. Ball knob thermoset PF 31. Accessories steel. Version: Black oxidised. Housing black. Ball knob, red. Accessories black oxidised.Note:The travel path is 10 mm. Self-locking occurs in ...

ZPH pipe clamps are specially designed for the quick and easy instalment of disc nozzles onto pipes. These clamps are very convenient as there’s no need to buy expensive metal tips or welded nozzle tips. You must drill a 19 mm diameter ...

ZPF swivel clamps are specially designed for HGQ, RGN and ZBA series. To install them on pipes all you need is drill a hole, insert the nozzle clamp inside and fasten it with a simple screwdriver. The nozzle clamp body is in PP chemically ...

ZPQ cam and lever clamps are specially designed for HGQ, RGN and ZBA ball nozzles. Only three steps to install them on a pipe: drill a hole, wrap the cam around the pipe and pull the lever down to block it. No need of tools. The body ...

Clamping force: 0.3, 0.5, 0.7 kN

Cam clamps, steel with tension lever Material: Carbon steel. Version: Black oxidised. Note: Dimension A refers to the distance from the workpiece to screw centre (cam screw). Form B with clamp plate is recommended to minimise scratches ...

Material: Cone, steel. Balls, ball bearing steel. Version: Cone hardened and ground. Balls embedded in rubber which is vucanised on the cones. Note: In conjunction with the position bushings, the position cones form a centring ...

Centring clamps Material: Body steel. Bushes carbon steel. Version: Black oxidised. Note: These centring clamps allow workpieces to be centred on and clamped in a bore. The clamps have a wide expansion range. The series covers a bore ...

High holding torques without additional air Increased safety due to safeguarding of the rotation axis Simple state query Efficient and fast process flow Market leading cycles Leakage-free thanks to proven piston seal

Rigid clamp for fixing to all profiles Standard with pivoting Slot nut and screws

Adjustable clamps for fixing to all profiles Standard with pivoting Slot nut and screws

These are the original type of shaft clamping elements, proven in a wide range of applications and available for shaft diameters from 20 to 50mm. Suited to more general applications, this series provides medium torque transmission, which ...

Design: Pneumatic clamping station for setting time-optimised clamping on machine tables with groove spacing of 63, 100 and 125 mm. Fastening is via M12 socket head screws. At least two fitting bores are attached for alignment. The insertion ...

Pneumatic unlocking. Opening operating pressure: K10.3 min. 5 bar. K20.3 min. 4.5 bar. Steel, unhardened. Repeat accuracy < 0.005 mm. Pneumatic clamping station for setting time-optimised clamping on machine tables with groove ...

Perpendicularity: 0.01/200 mm Material: aluminum casting Alignment hole and centre hole: with hardened bushes in accordance with DIN 179 with clamping and base surface Base surface: with hole pattern according to table or drawing, suitable ...

The permanent clamping magnets MSB are used for clamping of shaped parts and grinding of cemented carbide. Applications - For clamping of shaped parts - For grinding of cemented carbide (type SmCo) Features - Permanently magnetic - ...

The clamping magnets SPM belong to useful accessories for clamping of small parts. Applications - Ideal for grinding and electric discharge machining, measuring and testing jobs - Small magnetic workpieces from 0.5 mm can be clamped Features - ...

Clamping force: 10 kN

Clamp difficult or easily deformable workpieces In daily use you are optimally equipped with the TOPlus or SPANNTOP chucks. However, there are always components that are difficult to clamp due to the contour, or that will be deformed ...

The hydraulically-operated bore clamp is particularly suitable for clamping in workpieces with smooth bore holes in the support surface ranging from 8 to 12 mm in diameter. The workpiece is put directly onto the hardened surface of the ...

Clamping force: 1.3 kN

Mini compact clamp Advantages ● Minimum dimensions (Ø 22 mm) ● Partially immersed body ● Space-saving integration by a patented fixing principle ● Housing can be rotated by 360° ● Mounting without pipes ● Workpiece clamping without ...

Clamping force: 2 kN - 22.8 kN

Swing clamps with sturdy swing mechanism Advantages ● 4 sizes available ● Compact design partially recessible ● Very high clamping force already at 70 bar/120 bar ● Sturdy swing mechanism ● Very short clamping time ● Insensitive ...

Designed for holding insulated cables and wire. The sample is secured by the cam, which self-tightens as a load is applied and spreads the load evenly. Serrated cams are preferred for materials which may be slippy and so need a 'bite' ...

Clamping force: 16 kN - 40 kN

Indipendent and mobile standard sections vises. Extreme versatility and independence Gerardi Modular Elements allow you perfect clamping even of big workpieces which need the heaviest machining using the machine table as surface. Modular ...

Clamping force: 50,000 N

Fail-safe rail clamp with spring applied braking and hydraulic releasing. Designed for sideways clamping of rails and custom installation possibility (front or top) with included hydraulic power pack. (Area of) Applications Parking ...

Clamping force: 2,500 N - 200,000 N

spring activated – hydraulically or pneumatically released hydraulically released Features - Code Clamping Unit - K Standard - E Sizes are available for selection - 032 to 160 Spring activated - F Hydraulically released ...

Clamping force: 1,000, 1,600, 2,500, 4,000, 6,300 N

spring activated – hydraulically or pneumatically released pneumatically released Features - Code Clamping Unit - K Standard - E Sizes are available for selection - 040 to 100 Spring activated - F Pneumatically released ...

centres the hub to the shaft very high transmissible torque Features Centres the shaft to the hub Very high transmissible torques For shaft diameters between 20 mm and 180 mm

Clamping force: 22, 1 kN

The stainless steel swing clamps with helical rotation are dedicated to challenging environment. The design of this cylinders allows the use of borated or demineralized water, eliminating any risk of pollution of a clean medium. Field ...

Clamping force: 0.2, 24 kN

The swing clamps can clear the working area to facilitate components loading and un-loading operations. Designed for self-controled systems, they reduce non-productive time. The swing clamp with helical rotation is an economical solution ...

Clamping force: 0.5, 24 kN

The swing clamps can clear the working area to facilitate components loading and un-loading operations. Designed for self-controled systems, they reduce non-productive time. The planar rotation is an exclusive system which reduces ...

Jergens fixture plate machining kits consist of extra-long Ball-Lock shanks and spacers. These kits allow a fixture plate to be installed on a subplate with clearance between the plates. When a user is initially building a fixture on ...

Clamping force: 4,800 N

Jergens Swing Clamps are designed to swing 80° away from the workpiece to allow easy accessibility for part insertion or removal. Swing Clamps may be used in any attitude. The clamping arm may be positioned to swing either to the left ...

Clamping force: 8.5 N

Each charger, booster or starter comes with a pair of clamps suitable for the device’s wattage. As the battery-charging clamps will wear out faster than the equipment to which they are fitted, GYS sells replacement clamps. These items ...

Each charger, booster or starter comes with a pair of clamps suitable for the device’s wattage. As the battery-charging clamps will wear out faster than the equipment to they are fitted, GYS sells replacement clamps. These items are sold ...

Each charger, booster or starter comes with a pair of clamps suitable for the device’s wattage. As the battery-charging clamps will wear out faster than the equipment to which they are fitted, GYS sells replacement clamps. These items ...