Concentration analyzers

... long-term equipment protection, and optimize the process before injection into the natural gas grid. ProCeas® RNG / biogas analyzer delivers continuous, accurate, and multigas measurement, supporting critical stages of biogas pre-treatment, ...

... ® is also used to measure the concentration of O2 in CO2. All of this ensured the high quality and success of our research project. Key factor was the identification of the reaction by variation of impurity concentration.” ...

... The LaserCEM® is a turnkey multi-gas emissions monitor for environmental compliance, using two patented technologies: OFCEAS® (Optical Feedback Cavity Enhanced Absorption Spectroscopy) and LPS® (Low Pressure Sampling). QAL 1 certified by MCERTs and ...

... portable type, it is powered by Li- ion battery and can be used without AC power supply. It is used for measurement of the concentration of CO ,CO2 and O2 in sample gases simultaneously, calculating combustion efficiency and Lambda. It ...

... gas analyzer can be used for measurement of the concentration of automobile emission gas CO ,CO2 ,HC ,O2 and NO (optional). It is based on the pulsable infrared source and single source two beams non-dispersion infrared ...

... Gasboard-3000E is an analyzer for control of exhaust gases from gasoline, petrol, alcohol or LPG engines. It is developed based on Micro-flow NDIR technology for the measuring CO, CO2, O2 and NO exhaust gases. Features • Simultaneous ...

... measurement of: NOx, SO2, CO, O2, residual H2O, CO2, CH4 and N2O (greenhouse gases) • Environmental-friendly and cost-saving analyzer, with ultra low power consumption • No compressed air required (if using a gas cooler) • Insensitive ...

... volatile organic compound (VOC) analyzer. For this specific model, it can be used for a wide measurement range of about 0-10 to 0-30,000 ppm. Also, it features its TÜV and MCERTs QAL1 certification. Plus, the analyzer ...

... infrared method (NDIR-GFC) with gas filter correlation. O2 is measured by a built-in SRM paramagnetic sensor.

The analyzer has been designed to meet the specific needs of on-site regulatory measurement providing superior mobility, ...

... The airmoF is an automatic analyzer designed for continuous, real-time monitoring of formaldehyde in air. Using microfluidic Hantzsch reaction with fluorescence spectrometry, it delivers high sensitivity (down to 0.1 ppb), excellent accuracy, ...

... Product overview

• microF is a portable formaldehyde analyzer for continuous, real-time HCHO measurement in industrial environments and air quality studies. It combines a photomultiplier detector with microfluidic

... Light Volatile hydrocarbons and 1,3-Butadiene analyzers The airmoVOC C2-C6 is designed for the measurement of volatile hydrocarbons compounds from C2 to C6. The instrument uses a 6-port valve with a single sorbent trap and a metallic ...

... flue gas analyzer, it can measure ultra-low range (0-50mg/m3) of SO2 and NO, which is widely used in industrial emission monitoring to ensure the compliance with local emission regulation. Features • Accurate measurement of low concentration ...

... micro-flow NDIR technology to measure low concentration gases. (US Authorization No.: US11079322). • Adopting Micro-Flow NDIR gas sensor technology, high precision and long life time. • Monitoring low range concentration ...

... Introduction Gasboard-5020 emission gas analyzer is designed for measuring the emissions of all gasoline, LPG or CNG vehicles, it is developed based on the dual beam non-dispersion infrared (NDIR) principle to measure CO, CO2, HC, and ...

... Advanced digital CEMS analysis from the 4900 Multigas The 4900 Multigas is a high-performance CEMS analyzer designed for a wide range of multi-gas measurements. A complete monitoring solution for CEMS gas analysis A no-compromise ...

... exceptional performance operational flexibility in a compact unit. With an intelligent and robust hardware/software design, this analyzer can be moved easily from port to port, virtually eliminating dry down times often associated with ...

... The DF-745 SGMax moisture analyzer is optimized for specialty gas applications A Tunable Diode Laser (TDL) sensor-based trace moisture analyzer, the DF-745 SGMax is designed for the measurement of diverse gas mixtures ...

... effect. The oxygen concentration control ensures complete combustion, thus reducing CO2, SOx, and NOx emissions and helping prevent global warming and air pollution. BENEFITS Benefits of the Zircomat zirconia stack oxygen gas analyzers ...

... For Mission Critical Industries Our MBW CALIBRATION™ MODEL 373™ Dew Point Chilled Mirror Analyzer has been measuring humidity for almost 20 years. Incremental development based on operational experience and customer feedback means that ...

... Our MBW CALIBRATION™ MODEL 973L™ Dew Point Chilled Mirror Analyzer has a completely new design with an optimal Response Injection System for fast measurement. It is the first transportable analyzer to include mirror ...

... lithium battery, AC/DC dual use • Display: Color LCD touch screen with graphic menu The Huazheng HZSF-641 SF6 Comprehensive Analyzer integrates measurement of dew point, gas purity, and decomposition byproducts (SO₂, H₂S) into a single ...

... PCE-RCM 10 is a portable handheld dust particle measuring device or particle counter used to monitor particulate matter (PM) concentrations in the air. Designed to aid in indoor air quality (IAQ) assessments, this particle counter also ...

... Interface) The ILA1-B000-EX In-situ Laser Analyzer measures sulfur dioxide (SO2) in real time and is designed for industrial applications as well as for use in potentially explosive atmospheres. The analyzer requires ...

... towards other sample gas components, the portable M&C oxygen analyzer PMA10 has a wide variety of applications. The analyzer is a suitable and reliable instrument for measuring oxygen concentrations in ...

... sensitivity from other sample gas components, the M&C oxygen analyzer PMA20 has a wide variety of applications. The analyzer is a suitable and reliable instrument for measuring oxygen concentrations in ...

This series of analytical instruments are disinfectant analytical instruments with a microprocessor. The instrument adopts an LCD liquid crystal display screen, and intelligent Chinese/English menu operation. It has current out put, a wide measurement ...

... treatment, and industrial cleaning, this analyzer combines reliability, flexibility, and long-term durability to support critical process monitoring.

Product Introduction
Peracetic Acid (PAA) Analyzer ...

... The Online Residual Chlorine Analyzer is equipped with a German-made CS4 sensor, utilizing a special osmotic membrane technology that resists chemical interference (mainly from surfactants) and reduces pH dependence. The sensor is unaffected ...

... Product Overview
The FWTest™ Kit is a high-precision portable analyzer designed for measuring the concentration of ferromagnetic wear debris in oil. It is ideal for monitoring the condition of lubricated equipment ...

... The ferrous debris analyzer ERATEST FERRO is a mobile and battery-operated measuring instrument for determining the total content of ferromagnetic wear particles in oils or greases samples within only one second. The instrument operates ...

... Mobile field laboratory with electric cable contact gauge for measuring the water level, temperature and other water quality parameters (e.g. oxygen, pH, conductivity, redox potential, turbidity) in groundwater and surface waters SEBA Plug-in System ...

... Mobile, compact field laboratory for measuring water quality parameters (e.g. oxygen, pH, conductivity, redox potential, turbidity) in surface waters Spiral cable with stainless steel coupling for SEBA multi-parameter probes of the MPS-D3/D8/K16 3-line ...

... S605 Portable Breathing Air Analyzer offers a cutting-edge solution designed to ensure the highest standards of safety and quality in breathing air filling stations and breathing air systems. This state-of-the-art analyzer ...

... GOLD ADVANCE Wally precious metal analyser is a widely used, popular and reliable method for determining the elemental composition and purity of precious metals. Compared to other methods of analysis, using an analyser ...

... The GOLD ADVANCE S precious metal analyser is a widely used, popular and reliable method for determining the elemental composition and purity of precious metals. Compared to other methods of analysis, using an analyser ...

... Meets the requirements of IP standards: 336, 496 The analytical range of the 88 OIL ADVANCE instrument goes from a concentration of 4 ppm to 10%: it is equipped with an SDD detector with Peltier cooling, spectral resolution <130eV ...

... The SCHMIDT + HAENSCH Purity Analyzer is an inherent component in the analysis of sucrose content. It is applied at payment laboratories of the cane and beet sugar receptions. The modular design of the instrument enables you to automatically ...

... and prepared for polarimetric and refractometric measurements. The Purity Analyzer combines refractometric concentration measurements (Brix) with near-infrared polarimetry. Checkpoints Automatic on-line analysis ...

A fast and accurate analysis of the liming process is an important step in juice purification in a sugar factory. The on-line process analysis enables continuous process monitoring of the beet juice, enabling immediate process regulation. The automated ...

... Experience highly accurate and precise oxygen analysis – even in the low ppm range - with our rapid OXY cube. This oxygen analyzer delivers matrix-independent results as sample pyrolysis takes place at 1,500 °C in an extra-long furnace ...

... into one analyzer, the trace SN cube works as two analyzers in one box. This concept allows the specific optimization of the determination for each element. This ensures sulfur and nitrogen analysis with highest precision ...

... Experience matrix-independent, low-level nitrogen and carbon concentration measurements in solids and liquids with the UNICUBE trace. This elemental analyzer utilizes safe, user- and eco-friendly high-temperature combustion ...

... Features : gas return system Standard version • battery operation and/or external power supply • indication of moisture concentration in dew point °C or °F, referred to atmospheric or inlet pressure, reversible to indication in ppmV, ...

... storage of measuring results Features : WiFi Features : gas return system Standard version • indication of moisture concentration in dew point °C or °F, referred to atmospheric or inlet pressure, • reversible to indication in ppmv ...

... • battery operation and/or external power supply • indication of moisture concentration in dew point °C or °F, referred to atmospheric or inlet pressure, reversible to pm, or ppmw • indication of inlet pressure in bar, psi, MPa, and ...

... RA-915M is a supersensitive and highly selective portable analyzer that allows real-time mercury measurement in ambient and indoor air. Being combined with dedicated attachments, the analyzer is used for mercury determination ...

... standards such as ASTM D6722, D7622, EN/TS 17286, US EPA 7473, 30B, PS12B, SN/T 4429.2-2016, HJ 923-2017, and others. RA-915M analyzer can be used separately for real-time mercury measurement in ambient and indoor air. Other Lumex Instruments ...

... or argon), air is used as a carrier gas No pre- concentration on gold traps increases analysis speed and reduces exploitation complexity No memory effect: a sample with low mercury concentration can be analyzed ...

... The in situ analyzer of the cross-stack type is able to perform the average measurement of carbon monoxide over the entire section of the chimney. With no parts in contact with the process and with only the presence of the barrier air, ...

... The iCOMB line offers solutions for industrial applications with the use of in-situ analyzers capable of carrying out the measurement directly in the chimney, without the need for sampling and treatment of the sample gas, for the oxygen, ...

... Detcon Model 1000-CO2 and Model 1000-H2S Analyzers are designed to provide continuous, accurate, real-time measurement of gas concentrations in a wide variety of process gas streams. The instrument package is rated for ...

... Ion sensitive determination of Ammonium, Nitrate or Fluoride Low operating costs due to reagent free operation Minimal maintenance due to integrated sensor cleaning Flexibility to monitor additional parameters with ion sensitive electrodes ...

... Differentiated photometric determination of chlorine according to AWWA 4500-Cl G / EN ISO 7393-2 Continuous and simultaneous analysis of free, bound and total chlorine Freely adjustable measuring intervals for optimized use of reagents Fast and easy ...

... Automatic, continuous measurement of total chlorine in potable water, sanitary water, cooling water and effluent. Continuous online determination of disinfectants based on the DPD colorimetric method (EN ISO 7393-2; APHA 4500-Cl G). Measurement ...

... Many questions about foam, one universal approach: The DFA100 Dynamic Foam Analyzer measures the foamability of liquids and the stability of quickly decaying or long lasting foam based on reproducible foaming and height detection. With ...

... The elemental analyzer ELEMENTRAC CS-i measures the carbon and sulfur concentration in predominantly inorganic samples through combustion in an induction furnace and the subsequent analysis of the gaseous combustion products ...

The ELEMENTRAC CN-r is the ideal choice for high-capacity labs requiring quick and precise measurements of nitrogen, protein, and carbon. Utilizing Dumas analysis, it offers a reliable and efficient alternative to the traditional Kjeldahl technique for ...

... oil, coal and coke, ELTRA offers the combustion analyzer ELEMENTRAC CS-r with IR detection. The CS-r with up to 4 infrared cells is designed for carbon and sulfur measurement over a very wide concentration range. It ...

... The MAT1100 is the right choice whenever you only need to be concerned with the oxygen concentration or whenever only nitrogen is used. Its electrochemical oxygen cell (EC) measures within the range of 0.5 and 35 volume per cent and with ...

... If you need to measure the concentrations of oxygen and carbon dioxide, then the MAT1200 will be the appropriate model. In addition to an electrochemical oxygen cell, it features a non-dispersive infrared sensor (NDIR) for the CO2 measurement ...

... zirconium dioxide sensor (ZrO2) of the MAT1400 measures the oxygen concentration over the entire measurement range between 0 and 100 volume per cent. Especially in case of a very low concentration, it will achieve an ...

... Infrared Water Vapor Transmission Rate Tester

Product Introduction
W416 2.0 Infrared Water Vapor Transmission Rate Tester is an upgraded high-end precision testing instrument developed by GBPI R&D team in accordance ...

... Built-in 11.6" color touch screen with real-time display of up to five curves (permeation rate, temperature, humidity, concentration vs. time), one-key test and automatic shutdown.

... medicines. Nowadays, the headspace gas analyzer has become an important method to check the quality of packaging design and one of the important methods to verify the product shelf life. Our headspace gas analyzer GB-DK1 ...

... safety monitoring

• One process gas analyzer instead of several single gas devices
• Up to 8

... The BioBasic Biomethane is a biomethane analyzer that monitors product gas quality after biogas upgrading, directly at the grid injection point. It measures CH4, CO2, O2 and H2S every second, so operators see a deviation while it develops ...

... The BioBasic is a biogas analyzer for continuous online monitoring of raw biogas, digester gas and landfill gas, for quality control and process control on the plant. As standard it measures methane (CH4) and hydrogen sulfide (H2S); CO2, ...

... Product overview: TOC-50 is a multi-point Total Organic Carbon (TOC) analyzer developed by Labgeni for quantitative determination of TOC in water samples. The system comprises a central data terminal and up to 8 independent detection ...

... Packing list and contents available on product page images.

Technical specifications

• Category: TOC Analyzer
• Model / SKU: TOC-200B
• Measuring range: up to 3000 ppm
• Signal management: proprietary

... Short description
TGA1005 thermogravimetric analyzer (TGA) records sample mass change versus temperature or time during heating, cooling or isothermal processes to assess material thermal stability and composition. Applicable ...

... Double-Grounded Circuit Breaker Analyzer performs precise mechanical characteristic measurements for high-voltage circuit breakers (oil-minimum, oil-bulk, vacuum, SF6) across voltage levels. The Double-Grounded Circuit Breaker Analyzer ...

... Comprehensive Analyzer is a portable integrated analyzer for SF6 gas combining dew point (humidity), purity and decomposition-product analysis for on-site inspection of GIS and high-voltage switchgear.
Key ...

UHV-620 SF6 Micro Water Tester is a portable instrument designed to accurately measure dew point and trace moisture content in SF6, air, N2 and other non-corrosive gases. It is intended for on-site testing, gas acceptance and filling monitoring, and maintenance ...

It is applicable in the industry such as electrical power, coal, commerce inspection, environment protection, metallurgy, papermaking, petrochemical, earth probe and the research institute or quality inspecting organization to test the content of inner ...

DM2400S/ Cl monochromatic excitation energy dispersive X-ray fluorescence micrometer for sulfur and chlorine, referred to as DM2400S/ Cl MEDXRF micrometer for sulfur and chlorine. It uses the following technologies and devices to realize monochromatic ...

... technology, complying with the latest development in Computer technology. One PC could control 1 4 sets microwave moisture analyzer, or integrated into a multi-function meter with other instruments, realizing one PC control multi-instrument. ...

... On-line monitor with microprocessor control for water hardness analysis (with display of water hardness) Two set points of alarm from English degrees: 0,03 – 37,59°e ppm: 53,4 – 534ppm mg/l: 53,4 – 534 mg/l mmol/l: 0,004 – 5,3 mmol/l French degrees: ...

... Analysis of water hardness (with good water/not good water signal) Multifunctional microprocessor analyser for water hardness analysis with alarm set point for: French degrees: 0,05 / 0,09 / 0,18 / 0,36 / 0,54 / 0,9 / 1,8 / 3,6 ...

... Definitely the correct and reliable measuring value Since 2012 … our DUROMAT analysers stand the test in the daily use. The DUROMAT XX is used to monitor the limit value. In addition to the current measured values, the display also ...

... , Afera 4015, Afera 5001, Afera 5004.

What is the application of texture analyzer in food industry?
The application of a texture analyzer in the food industry involves assessing the physical ...

... The DK-190 Headspace Gas Analyzer adopts a new handheld design and is equipped with imported sensors, which can accurately and conveniently determine the O2, CO2, N2 content in sealed packaging bags, bottles, cans, and other hold packaging ...