- Hydraulics - Pneumatics >
- Valve >
- Valve >
- Nordson
Nordson valves
Pressure: 15 bar - 300 bar
Temperature: -20 °C - 100 °C
DPA PROGRESSIVE DIVIDERS LUBRICANT DISPENSING SEQUENCE The initial piston dispenses lubricant to the outlets corresponding to the final piston. The final piston dispenses lubricant to the outlets corresponding to the central piston ...
I.L.C. srl
... lockup valve is open and allows the free flow of compressed air from the positioner to the pneumatic actuator. When the lockup valve loses its signal (or it drops below an adjustable set point), the lockup ...
Max-Air Technology
DN: 10 mm - 25 mm
screw connection G 3/8” – G 1” DN10 – DN25 material specifications housing, not in contact with medium: POM plastic (polyoxymethylene), natural white threaded cover: POM plastic (polyoxymethylene), natural white srews: galvanized ...
Ho-matic
DN: 25 mm - 150 mm
Pressure: 10 bar
Temperature: -10 °C - 25 °C
... different applications and products Easy maintenance without the need for special tools Sturdiness: valve bodies made from solid bar The BZAW3 is a double seal valve designed to guarantee separation ...
BARDIANI VALVOLE S.p.a.
Pressure: 0 psi - 145 psi
Temperature: -20 °C - 70 °C
1、Exhaust outlet locates over the body, which is convenient to install muffler to decrease noise and pollution; 2、The external force required by direction-change of series of M5B, M5R and M5L is provided by external mechanism, which ...
Airtac Automatic Industrial
Circulation control valve Tasks Circulation control valves regulate the flow rate during drum circulation on forced-flow steam generators. Versions Forged valves in straight, angled ...
Welland & Tuxhorn AG
Low-load start-up control valves supply the boiler with the required quantity of feedwater during start-up (30–50% of the water required for full-load operation), regulated by volume, at higher pressure differences than ...
Welland & Tuxhorn AG
Injection control valve Tasks Injection control valves are primarily flow control valves, which means they supply the required amount of cooling water to the point of use. The pressure ...
Welland & Tuxhorn AG
DN: 0.25, 0.125, 0.43, 0.56 in
Pressure: 10,000, 6,000 psi
Compact size valve built for maximum durability and robust performance in the toughest applications 100% helium leak tested to 1 x 10-4 ml/s for guaranteed performance and reliability Hard seat valves ...
NOSHOK
Pressure: 29.4, 31.6, 35.7, 42.2, 49.6 bar
Temperature: 38, 100, 200, 300, 400 °C
... all stop valves and with test and drainage function. The TrapStation TS 36 encompasses the universal connector, two stop valves - which are accessibly positioned and clearly colour-coded to ensure easy ...
GESTRA AG
DN: 4, 6 mm
Pressure: 1 bar - 10 bar
Temperature: -10 °C - 150 °C
Valve NBZ-5 is a nebulizer of liquids with venturi effect operation and adjustable spout by means of a knurled ring. It is especially suitable for following uses : Lubrication of machine members. Lubrication and cooling ...
Bonesi Pneumatik s.r.l.
DN: 0.25, 0.125 in
Pressure: 1 bar - 10 bar
Temperature: -10 °C - 70 °C
The SLT circuit switch allows to convey two pneumatic signals into one way, keeping the two pneumatic sources separated. They have aluminium body, NBR seals and brass components and are available with 1/8” and 1/4" ports. CONSTRUCTIVE ...
Bonesi Pneumatik s.r.l.
DN: 0.5, 0.25, 0.125 in
Pressure: 1 bar - 10 bar
Temperature: -10 °C - 70 °C
UM series one way valves are used when there is the need to keep under pressure one tube, allowing, at the same time, the flow if air to one way.
Bonesi Pneumatik s.r.l.
Planning, construction and delivery of high quality valves for power plant and process heat generation.
At ARIS, you receive high-quality electrical and pneumatic actuators and robust industrial fittings. We supply individual products for self-assembly or replacement drives and accessories. Of course, we also assemble ...
Pressure: 0 psi - 5,500 psi
The Series MV High Pressure Gas Control Valve is optimized for the demanding requirements of Gas Cylinder Fill Plants, Manifold, and Piping System applications. The High Pressure Oxygen Service Valve ...
Generant
DN: 2.5 mm
Smooth operating spindle made of PTFE, valve bore: 0-2,5 mm, with retaining device to avoid complete unscrewing, screw cap and retaining device made of PP, operating temperature: -20 to +150 °C, made of DURAN® tubing, ...
DN: 250 mm - 3,000 mm
The dapò valves are widely used where a regulation of the flow rate or a partialization of the air flows is required. Dapò adjustment valves with diameters from 250 mm up to 3000 mm are possible. For ...
... Rimor manufactures guillotine valves for all those applications where it does not have to be present – with the valve open – no impediment to the flow of fluid eg shavings and so on, this can not be achieved ...
Pressure: 0 Pa - 2,000 Pa
Temperature: 0 °C - 1,000 °C
As for industrial round valves, square valves are also designed taking into account the pressures and temperatures of use. The industrial square valves do not have a standard dimension, ...
The fast-closing float anti-explosion valve prevents propagation of flame and pressure during explosion to other production equipment. This valve is intended for protection of pipe transport systems.
RSBP spol. s.r.o.
DN: 10 mm - 600 mm
... CERAMIC INDUSTRY, as a shut-off valve for solids, sludge, etc. ENVIRONMENTAL TECHNOLOGY, for sealing waste water, dust, sludge, etc. WATER TREATMENT/SEWAGE TREATMENT PLANTS, as a shut-off valve ...
AKO ARMATUREN
DN: 10 mm - 250 mm
Pressure: 2 bar - 6 bar
... operated Pinch Valves. What are the benefits of air operated pinch valves? Free flow of product, minimum frictional resistance, 100% leak free, no blockages and low net weight are among the most important ...
AKO ARMATUREN
DN: 25 mm - 150 mm
Pressure: 6 bar
... air operated pinch valves can also be provided in compliance with DIN 11853-2 and DIN 11864-2 Form A. Air Pinch Valve, VMC Series, Stainless steel design, ANSI B 16.5-150lbs Air operated pinch valve ...
AKO ARMATUREN
DN: 0.75, 0.5 in
Pressure: 150, 300 psi
Temperature: 358, 550 °F
... Control Four-V Port Globe Valves are equipped with a micrometer dial and pointer which enables the valve to set within 1/100th of a turn of the handwheel. This allows you to fine-tune the blowdown flow ...
Walchem
DN: 0.5, 0.75, 1 in
Pressure: 250 psi
Temperature: 400 °F
The Motorized Ball Valve delivers a torque of 150 in-lbs using a non-reversing motor, opening the valve in 5 seconds and minimizing pressure hammer. The motor is protected in a NEMA 4X enclosure and features ...
Walchem
DN: 0.5 in
Pressure: 30 psi - 125 psi
Walchem’s economical Tri-Purpose Valves are three valves in one. Installed in one direction, the spring loaded PTFE faced diaphragm provides 30 psi of back pressure and anti-syphon protection. Installed ...
Walchem
DN: 40 mm - 125 mm
Pressure: 6, 16 bar
Temperature: -20 °C - 80 °C
The asa butterfly valve with SAE and DIN flange connections allows the combination with an elastic element (rubber compensator expansion joint) to make a short compensating and economical connection with the pump port. ...
DN: 40 mm - 70 mm
Pressure: 6, 16 bar
Temperature: -20 °C - 80 °C
The asa butterfly valve with SAE and DIN flange connections allows the combination with an elastic element (rubber compensator expansion joint) to make a short compensating and economical connection with the pump port. ...
DN: 50, 65, 80 mm
Pressure: 0.5 bar - 1.5 bar
Temperature: -20 °C - 80 °C
The asa butterfly valve with SAE and DIN flange connections allows the combination with an elastic element (rubber compensator expansion joint) to make a short compensating and economical connection with the pump port. ...
DN: 0.5 in - 12 in
Pressure: 175 psi
Temperature: 121 °C
... Bell & Gossett, assures optimum system flow balance at minimum pump operating horsepower. Valves can simply be pre-set using the B&G Circuit Setter Balance Valve Calculator, curve booklet G10091, or the ...
Bell & Gossett Domestic Pump
DN: 0.5 in - 6 in
Flow rate: 0 us gal/min - 880 us gal/min
... calculations when selecting control valves Always maintains 100% authority, ensuring excellent control Combination valve reduces cost and more accurate flow control lowers lifecycle costs ...
Bell & Gossett Domestic Pump
DN: 0.15 in - 1 in
Pressure: 10 bar
Temperature: 93 °C
Combines three valves in one: Isolation Valve, Check Valve and Companion Flange Free floating flange allows easy alignment and installation of pumps Prevents gravity circulation Isolates ...
Bell & Gossett Domestic Pump
Pressure: 28,000,000 Pa
Temperature: -20 °C - 100 °C
Flow rate: 0 l/min - 120 l/min
... swing motor LS control + constant horsepower control Good for straight traveling of wheel motors Various kinds of attached valves
NACHI America
DN: 8 mm - 50 mm
Pressure: 63 bar
Temperature: -25 °C - 180 °C
industry, high temperature, high pressure PRESSURE PFA/PS in bar BODY : CF8M BALL : Stainless steel 316
SOCLA
DN: 8 mm - 80 mm
Pressure: 63 bar
Temperature: -25 °C - 180 °C
industry, high temperature, high pressure PRESSURE PFA/PS in bar BODY : CF8M
SOCLA
DN: 15 mm - 50 mm
Pressure: 100 bar
Temperature: -20 °C - 100 °C
industry, high temperature, high pressure PRESSURE PFA/PS in bar BALL : stainless steel 316 - SEALS : PTFE SPECIAL : ISO EN 5211 top connection, actuation possible
SOCLA
DN: 3, 5.5 mm
Pressure: 20 bar
Temperature: -20 °C - 80 °C
2/2-way socket ball valve Micro brass design chromed with connection connector and male R-thread Producer Material of casing: Brass chromed Material of ball: Brass hard-chromium plated Material of ball seal: PTFE Material ...
Mader
DN: 15 mm - 76 mm
Temperature: -10 °C - 170 °C
2/2-way ball valve brass design nickel-plated in medium heavy design with female G-/R-thread Producer Material of casing: Brass nickel-plated Material of ball: Brass hard-chromium plated Material of ball seal: PTFE Material ...
Mader
DN: 10, 15, 20, 25 mm
Temperature: -20 °C - 150 °C
2/2-way ball valve brass design nickel-plated with butterfly handle with male thread Producer Function principle: 2/2-ways Actuation type: manually Material of casing: Brass nickel-plated Material of ball: Brass ...
Mader
DN: 4 mm - 38 mm
Pressure: 350, 400, 500 bar
Temperature: -20 °C - 80 °C
Connection 1 + 2 BSP cylindrical internal threads Sealing form 1 + 2 for screw-in pins with shapes A, B and if necessary E Note Bitte die Bedienungsanleitung für Kugelhähne beachten. Bitte die zul. Druckangaben ...
HANSA FLEX AG
DN: 6 mm - 38 mm
Pressure: 400 bar
Temperature: -20 °C - 60 °C
Connection 1 + 2 BSP cylindrical internal threads Sealing form 1 + 2 for screw-in pins with shapes A, B and if necessary E Note Bitte die Bedienungsanleitung für Kugelhähne beachten. Bitte die zul. Druckangaben ...
HANSA FLEX AG
DN: 6 mm - 50 mm
Pressure: 25 bar
Temperature: -20 °C - 150 °C
Sealing form 1 - 3 Shape A Connection 1 - 3 BSP cylindrical internal threads Bore L shaped Contact travel 0°; 90° Surface nickel plated Material Brass housing Aluminium handle Brass ball, ...
HANSA FLEX AG
DN: 6 mm
Pressure: 500 bar
... high-pressure ball valves for plate mounting up to 500 bar. Block body design for manifold mounting with either 4 or 6 mounting holes for added safety; improved manifold design eliminates external piping and connectors. Ball ...
STAUFF
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining