Volumetric flow rate: 0.1 l/min - 10 l/min
Process temperature: 0 °C - 80 °C
Process pressure: 10 bar
... 7 segment flow rate indication Standardised button programming Can be used for water/glycol mixtures Flow and temperature monitoring ...
EGE-Elektronik Spezial-Sensoren GmbH
Volumetric flow rate: 2 l/min - 100 l/min
Process temperature: 0 °C - 80 °C
Process pressure: 20 bar
... 7 segment flow rate indication Flow rate and temperature Standardised button programming No parts protruding into the flow Switching and/or analogue output (combinations possible) Can be used for ...
EGE-Elektronik Spezial-Sensoren GmbH
Volumetric flow rate: 0.2 l/min - 80 l/min
Process temperature: 0 °C - 60 °C
Process pressure: 10 bar
... Flow rate sensor with amplifier Magnetic-inductive measuring principle Flow indication with bright red 3-digit 7 segment indication Set-up via buttons at the device ...
EGE-Elektronik Spezial-Sensoren GmbH
Volumetric flow rate: 2 l/min - 160 l/min
Process temperature: 0 °C - 85 °C
Process pressure: 0.1 bar - 2.3 bar
... Axial turbine flowmeter for liquids • For measuring the volume flow rate or for dosing tasks with large flow rates. • Compact design. • Wide useful operating range. • Wide variety ...
Volumetric flow rate: 0.15 m³/h - 0.9 m³/h
... Typical engine burn is ~100 L/h while fuel supply-line flow can reach up to 800 L/h. Installers often used two single-chamber meters in differential mode; DFM 900D consolidates that capability into one compact ...
Process temperature: 150 °C
Process pressure: 150 bar
... reagent in flue gas treatment and transport lines with very low material concentration Electrodynamic flow sensor for measurement of low flow rates from 0 to 100 kg/h. For pipe diameters up to 1 m. Ideally used ...
Process temperature: 0 °C - 120 °C
Process pressure: 10 bar
... or ducts • No real upper limit of mass flow • Maximum pressure 10 bar • Dust tight • No flow restrictions to the process flow (wear resistant ceramic liner) • The mass flow measurement ...
Process temperature: -20 °C - 60 °C
Process pressure: 0.6, 1.6, 4 MPa
Precision: 0.5, 0.2 %
... instantaneous pulsating flow with good linearity.
Process temperature: -40 °C - 60 °C
Process pressure: 4, 1.6, 1, 0.6 MPa
Precision: 0.2, 0.5 %
... cumulative flow during power-off.
Precision: 0.25, 0.4 %
Repeatibility: 0.5 %
... various sensor parameters, anticipating possible problems. The battery converter with integrated modem MV255, flow meters, energy meters, ...
ISOIL Industria Spa
Volumetric flow rate: 0 m³/h - 280 m³/h
Process temperature: -20 °C - 150 °C
Process pressure: 16 bar
... Description The sanitary sensor for electromagnetic flow meters MS 2410, flow meters, energy meters, ultrasonic flowmeters, and industrial automation systems have ...
ISOIL Industria Spa
Volumetric flow rate: 0.6 m³/h - 60 m³/h
Process temperature: -30 °C - 130 °C
Process pressure: 1.6 MPa
... ISONRG MV311, or it provides pulses directly, in a compact version and its power can be integrated battery or powered externally. The ultrasonic range sensor IFX-M4-01 ISOFLUX, flow meters, energy ...
ISOIL Industria Spa
Volumetric flow rate: 1.4 l/h - 500,000 l/h
Process temperature: -20 °C - 100 °C
Process pressure: 1.5 bar - 10 bar
... chemical compatibility with the flow medium and to offer different measuring ranges. Magnetic Float option is available to be combined with micro switches for MIN and MAX alarm, clamped on the guide of the flowmeter. ...
Volumetric flow rate: 21.24 m³/h - 11,326.74 m³/h
Process temperature: -18 °C - 121 °C
Process pressure: 34, 10 bar
... The Model ST50 is a compact, low cost solution for accurate, repeatable flow rate measurement of air, compressed air or nitrogen. This insertion-style flow meter has no moving parts and ...
FCI Fluid Components International
Process temperature: -18 °C - 121 °C
Process pressure: 34, 10 bar
Precision: 0.5, 1, 2 %
... ST51 and ST51A are a compact, low cost solution for accurate, repeatable flow measurement of biogas, digester gas, landfill gas, methane and natural gas as well as air, compressed air or nitrogen. This insertion-style ...
FCI Fluid Components International
Volumetric flow rate: 5.13 m³/h - 951.57 m³/h
Process temperature: -18 °C - 121 °C
Process pressure: 16.5, 41 bar
... The ST75 Series thermal flow meters are a compact, low cost solution for accurate, repeatable direct mass flow measurement of air and gases. These in-line (spool-piece) style flow ...
FCI Fluid Components International
Volumetric flow rate: 1.6 m³/h - 3,125 m³/h
Process temperature: -40 °C - 70 °C
Process pressure: 1 bar - 10 bar
... reasonably priced, most accurate flow meter tailored for your applications. A flowmeter with base functionality, short delivery and a simple and clearly understandable documentation. EPD Electromagnetic ...
Volumetric flow rate: 0 l/min - 300 l/min
Process temperature: -10 °C - 50 °C
Process pressure: 0.2 bar - 2 bar
... Built upon proven TSI flow sensor technology, the NEW 5000 Series Flow Multi- Meter redefines what a flow meter can do for you. This all-in-one gas mass flow ...
... 4000 SERIES FLOW METERS THERMAL MASS FLOW METERS DESIGNED FOR GAS FLOW MEASUREMENT The TSI 4000 Series was designed for ultra-low pressure loss to minimize flow ...
Process temperature: -30 °C - 80 °C
... cycle operation for self-sufficient systems Flow metering at the highest technical level The NivuFlow 750 flow meter is the successor to the well-known OCM Pro CF. Compact dimensions ...
NIVUS GmbH
Process temperature: -20 °C - 70 °C
... ambient conditions. The large graphic display permits quick and easy commissioning of the flow meter system. Due to the modular construction of our radar flow meter system we can provide ...
NIVUS GmbH
Process temperature: -20 °C - 70 °C
... operates over the full bi-directional flow range without causing obstruction or head loss where the large array of NIVUS transducer models permits flow measurement across the widest possible range of applications. The ...
NIVUS GmbH
Volumetric flow rate: 0.1 l/min - 1,670 l/min
Process temperature: -10 °C - 70 °C
Process pressure: 400, 200, 100, 64 bar
... EL- FLOW® Select series Mass Flow Meters/Controllers are thermal mass flow meters of modular construction with a ‘laboratory style’ pc-board housing. Control valves can ...
Bronkhorst
Volumetric flow rate: 0.4 m³/h - 11,000 m³/h
Process temperature: -10 °C - 70 °C
Process pressure: 100, 64, 40, 200, 400 bar
... IEC 61508 standard Compact and competitive Mass Flow Meters for high gas flow rates For consumption measurement of high gas flow rates, customers often select volumetric ...
Bronkhorst
Volumetric flow rate: 0.2 l/min - 166,666.6667 l/min
Process temperature: -10 °C - 70 °C
Process pressure: 10 bar
... For applications with only little differential pressure, Bronkhorst developed the LOW-ΔP- FLOW series mass flow meters and controllers. In these instruments, the flow resistance is minimized ...
Bronkhorst
Volumetric flow rate: 0.015 l/min - 83 l/min
Process temperature: -40 °C - 80 °C
Process pressure: 200, 50 bar
... Designed for precise flow measurement, the volumetric flow meter is suitable for continuous or intermittent monitoring of liquid flow or instantaneous flow ...
... easier. The S421 is the perfect meter to monitor your compressed air system and measure the compressed air flow and consumption. Features Easy and affordable sensor solution to measure the compressed air ...
SUTO iTEC GmbH
Process temperature: -30 °C - 70 °C
Process pressure: 0 bar - 10 bar
Precision: 1.5 %
... Thermal mass flow with no additonal compensation required Perfect to measure your compressed air flow and consumption Economic and affordable compressed air flow meter - S415 ...
SUTO iTEC GmbH
Volumetric flow rate: 121 m³/h - 43,870 m³/h
Process temperature: -40 °C - 120 °C
Process pressure: 0 MPa - 1.6 MPa
... S431 OEM Compressor Flow Meter for Wet Air is developed to measure the compressor performance inside or at the outlet of the compressor. The flow meter provides accurate and long-term ...
SUTO iTEC GmbH
Volumetric flow rate: 0 m³/h - 2,545 m³/h
Process temperature: -25 °C - 90 °C
Process pressure: 4, 2.5, 1.6 MPa
... Electromagnetic flowmeter type PEM-500 is applicable to the measurement of flow of the liquids with minimum conductivity of 5ěS/cm. Device measures flow and volume of liquids in both directions of flow. ...
Volumetric flow rate: 0 m³/h - 19.8 m³/h
Process temperature: 0 °C - 90 °C
Precision: 2 %
... Product Overview
The TAD series ultrasonic in-line
flow sensor from XY-TEK integrates sensing and signal processing in a
compact housing to provide
continuous liquid
flow measurement ...
XY-TEK
Volumetric flow rate: 0 l/min - 12 l/min
Process temperature: 0 °C - 60 °C
Precision: 3 %
... Overview
The CM series clamp-on ultrasonic
flow sensors /
flow
meters are
compact, non-invasive devices with embedded electronics. They attach to flexible plastic tubing to ...
XY-TEK
Volumetric flow rate: 0 l/min - 100 l/min
Process temperature: 0 °C - 60 °C
Precision: 3 %
... /strong>
The CM series clamp-on
flow sensors/
flow
meters are similar to CG series sensors/
flow
meters in basic structure and function. The major difference is that ...
XY-TEK
Volumetric flow rate: 0.0005 l/min - 10 l/min
Process temperature: -30 °C - 80 °C
Process pressure: 0 bar - 250 bar
... This new micro flow meter expands VSE’s RS series with an additional size. To allow for easy integration into a wide range of applications, the connection units follow the proven design of the standard RS series*. The ...
Process temperature: 0 °C - 60 °C
... >AI.C-SONIC is the cutting-edge solution for measuring water flow in small pipes. Thanks to "transit time" ultrasonic technology, this instrument allows precise flow monitoring without ...
ASIT ITALIA
Process temperature: -40 °C - 130 °C
Precision: 1 %
... battery that provides up to 16 hours of
continuous operation, all stored in a sturdy aluminum carrying case.
Main Technical Specifications
Accuracy: ±1% of the measured value
Flow Range: ...
ASIT ITALIA
Process temperature: -30 °C - 160 °C
Precision: 1 %
... the ultimate professional solution for precise liquid flow measurement in closed ducts. Based on transit-time ultrasonic technology, this system ensures accurate measurements without interrupting flow or cutting pipes, ...
ASIT ITALIA
Mass flow rate: 1 kg/h - 20,000 kg/h
Process temperature: -20 °C - 450 °C
Process pressure: 6, 30 bar
... Microwave-based flow measurement for bulk solids MF 3000 Numerous bulk material applications require continuous measurement of mass flow, e.g. for exact dosing of a material or to ...
Volumetric flow rate: 0.3 l/min - 140 l/min
Process temperature: -20 °C - 70 °C
... SONOFLOW CO.55 CLAMP-ON SENSOR - NON-CONTACT FLOW METERS FOR LIQUIDS IN FLEXIBLE TUBES The ultrasonic clamp-on flow meter SONOFLOW CO.55 measures the flow rate of ...
Volumetric flow rate: 18 l/min
Process temperature: 0 °C - 90 °C
... inlay for an optimal coupling between tube and transducer •No external electronics for a compact design and simple handling •Customer calibration for different flow rates ...
Volumetric flow rate: 14 l/min
Process temperature: 10 °C - 50 °C
... The hybrid flow-bubble sensors of the series SONOFLOW CO.56 Pro V2.0 and SONOFLOW CO.56 combine accurate flow measurement and reliable air bubble detection in liquid filled medical tubing. They feature a simple integration ...
Process temperature: -20 °C - 50 °C
... data memory RS-485 (Modbus RTU), USB Host, Ethernet communication panel, compact device in 96 x 96 mm case The MultiCon CMC-99 is a powerful and versatile compact-multichannel-controller with a capability ...
Process temperature: -40 °C - 85 °C
Precision: 1 %
... RQ-30 DISCHARGE MEASUREMENT WITH DATA LOGGER AND DATA TRANSMISSION IN COMPACT Housing The RQ-30 ADMS is an all-in-one discharge measurement System. It contains the non-contact flow velocity and water level sensors ...
SOMMER Messtechnik GmbH
Process temperature: -40 °C - 85 °C
Precision: 1 %
Repeatibility: 0.1 %
... even during high flow, floodings or despite of debris, driftwood or high turbidity. IMPLEMENTATION The sensor impresses with low power consumption and its high reliability for permanent recording of the flow velocity. ...
SOMMER Messtechnik GmbH
Process temperature: -40 °C - 85 °C
Precision: 1 %
... affected by debris and entrained solids. With its compact design and versatile mounting options, it is the ideal choice for flow measurements in manholes of facilities and sewers. FEATURES AND ADVANTAGES Non-contact ...
SOMMER Messtechnik GmbH
... measurement frequency from its front end. The reflected signal is used to measure the mass flow using a patented method and output as an analog signal proportional to the mass flow. Evaluation is done ...
Process temperature: -30 °C - 140 °C
Process pressure: 0 bar - 10 bar
... with BDL compact - volume flow measurement - Sensor SF53, 185 m/s, 220 mm insertion depth - Datenlogger BDL compact 2D - Connection cable approx. 5 m METPOINT®️ FLM monitoring and controlling the ...
Volumetric flow rate: 0.06 m³/h - 36 m³/h
Process temperature: -40 °C - 60 °C
Process pressure: 50,000 Pa - 300,000 Pa
... MFHD series of meters are designed for fuel cylinder management and can be used for natural gas metering as well. Its compact size covers residential fuel application ranges and opts to output fuel thermal values. The ...
the best suppliers