DN: 20 mm - 110 mm
... UU001UNION FACTORY PIPE-WORKSHOP FITTING WORKSHOP MOULDS WAREHOUSE MATERIAL PREPARE MATERIAL TESTING PRESSURE TESTING FOR VALVES PACKING LINE WAREHOUSE LOGISTICS SAMPLE DISPLAY SHOWROOM ...
DN: 80 mm - 100 mm
Pressure: 16 bar
... description
Butterfly
valve with EPDM O-ring, made from UPVC (U-PVC), available in DN80 and DN100 sizes (PN16).
Product details
- Brand: U-PVC Check Valves
- Category: Check Valves
- Type:
NEISCO FOR MODERN WATER SYSTEMS PRODUCTION
DN: 15 mm - 100 mm
Pressure: 10 bar - 16 bar
... Overview
UPVC double union ball
valve with adjustable seat and female plain ends.
Product Details
- Type: UPVC Ball Valves
- Brand: U-PVC Ball Valves
- Category:
NEISCO FOR MODERN WATER SYSTEMS PRODUCTION
DN: 15 mm - 100 mm
Pressure: 10 bar - 16 bar
... union UPVC ball
valve BVDL13 for fluid isolation, featuring an adjustable seat and BS female plain ends; available in sizes from 1/2" to 4".
Product details
- Brand: U-PVC Ball Valves
- Category:
NEISCO FOR MODERN WATER SYSTEMS PRODUCTION
DN: 0.75 in
Pressure: 5 bar
Temperature: -25 °C - 85 °C
... proportional flow control valve FC1500 and a MEMS gas flow meter. FC1500 is a highly refined needle valve driven by a micro step stepper motor. Turndown ratio can reach up to 400:1, with high accuracy, repeatability, ...
KaoLu
DN: 0.125, 0.375, 0.5 in
Pressure: 7, 5, 10, 20 bar
Temperature: -20 °C - 84 °C
... Proportional Flow Control Valve consists of PM series driver and FC series proportional flow valve. With an input signal either through analogue or digital, the needle inside the proportional valve moves ...
KaoLu
DN: 0.125 in
Pressure: 2 bar - 11.5 bar
Temperature: 0 °C - 70 °C
... proportional control valve. This series is an electronically controlled closed loop pressure regulator. The device converts a command signal to customers' specified pressure range. The QKL-B1HF consists of a control circuit board, one ...
KaoLu
... E-car Battery Pack ex-proof Vavle · Pressure equalization and release in order to extend seal life · Can open the valve rapidly when heating up under a abnormal status. · Prevent condensation · Block contaminants like ...
Shenzhen Milvent Technology Co.,Ltd
DN: 12 mm
Temperature: -40 °C - 125 °C
... Product overview
New low-profile M12x1.5 dual-stage vent
valve designed for battery packs, gearboxes, chemical and outdoor enclosures. Integrates a vent and
valve to maintain pressure balance during normal operation ...
Shenzhen Milvent Technology Co.,Ltd
Pressure: 100 mbar - 200 mbar
... Overviews Enclosures and containers: a look at their vulnerabilities and the role of Milvent Vents in preventing failure In the high-tech world of today, enclosures and containers are a crucial part of protecting sensitive equipment and ensuring optimal ...
Shenzhen Milvent Technology Co.,Ltd
DN: 0.5 in - 2 in
Pressure: 1 bar - 10 bar
Temperature: -15 °C - 100 °C
... pressure reducing valve that design and developed to sustain higher corrosive resistance for wider range of application. What is the function of Titanium Direct Acting Pressure Reducing Valve? Titanium Pressure Reducing ...
Elite Line Industrial Corp.
DN: 0.5 in - 6 in
Pressure: 1 bar - 13 bar
Temperature: -15 °C - 180 °C
... Model RET-DS / REF-DS are the Direct Acting Pressure Reducing Valve designed with Duplex Stainless Steel material providng more options for different industries. Pressure Reducing Valve protecting the system by reduce ...
Elite Line Industrial Corp.
DN: 1.5 mm - 56 mm
Pressure: 0 psi - 142.2 psi
Temperature: -15 °C - 80 °C
... / BFF, The float valve has one major function and that is to stop the flow of water from an inlet supply line. The float valve rises as the water level rises. Once a specified water level is reached, this will cause ...
Elite Line Industrial Corp.
DN: 15 mm - 65 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C
... DIALOCK® diaphragm valve with stroke limiter and male ends for solvent welding, metric series. The DK DIALOCK® diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The ...
FIP - Formatura Iniezione Polimeri
DN: 15 mm - 65 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C
... Pneumatically actuated diaphragm valve with male ends, metric series. Normally Closed function. The DK diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal ...
FIP - Formatura Iniezione Polimeri
DN: 125, 150 mm
Pressure: 10 bar
... The FE is a butterfly valve for shutting off or regulating flow, specifically designed for water conveyance applications. In addition to the manually actuated version, FE is also available in FE/ CE electrically actuated and FE/CP pneumatically ...
FIP - Formatura Iniezione Polimeri
DN: 0.125 in - 1.5 in
Pressure: 1 mbar - 670 mbar
Temperature: -20 °C - 120 °C
... Vacuum adjustment valves When these valves reach a certain pre-calibrated vacuum degree, they introduce atmospheric air into the circuit to prevent the increase of the set value and to keep it constant. They can be ...
VUOTOTECNICA
DN: 0.375, 0.5 in
Temperature: 220 °C
Flow rate: 20, 10 m³/h
... Suction valves for vacuum press bags The suction valves described on this page have been designed for a quick vacuum connection on press bags for composite fibre products. These valves are composed ...
VUOTOTECNICA
DN: 0.375, 0.472, 0.25, 0.5 in
... Plunger valves are composed of a cylindrical brass body, a steel plunger with a conical valve and a thrust spring. Connected to vacuum, they are normally closed. They activate suction, thus creating vacuum, only when ...
VUOTOTECNICA
... Bypass valve with pressure regulator valve, can be utilized in applications where the pump is operating constantly. ...
BEZARES S.A.
DN: 1, 0.75, 0.5 in
Pressure: 350 bar
Flow rate: 180, 120, 80 l/min
... Circuit selector valve, manual operation maximum pressure ...
BEZARES S.A.
DN: 1, 0.75, 0.5 in
Pressure: 400, 350, 500 bar
Temperature: -20 °C - 125 °C
... Pilling-Up directional control valve single or double acting. From 1 to 7 sections, with relief valve and multiple configuration options. ...
BEZARES S.A.
DN: 0.25 in
Pressure: 0 bar - 400 bar
Flow rate: 8, 4, 2 l/min
... Valve is controlled by compressed air acting on piston in the cylinder. Valve is kept open by the spring force. When pilot pressure is applied the valve closes. When pilot fluid is shut off the valve ...
DN: 4, 8, 6 mm
... The Burkle 2 and 3-way valves are utilized for transferring liquids or gases in order to release, block, or divert the direction of the flow. The PVDF-transparent framework allows optimum chemical resistance which makes it ideal for use ...
DN: 11 mm
Pressure: 0 bar - 4 bar
Temperature: 20 °C
... Ball valve PP fits all containers with G 3/4" connection thread. It can be attached to nearly all containers with thread adapters. Robust industrial quality, large flow. - Suitable for crystallising media - With connecting cap nut, guaranteed ...
DN: 0 mm - 10,000 mm
Pressure: 2,500 bar - 4,200 bar
Temperature: 5 °C - 50 °C
... Product description
Needle
valves provide a reliable means to shut off and regulate media. Designed specifically for extreme high‑pressure applications, these
valves are used in demanding hydraulic systems such ...
WEH FluidTech GmbH
DN: 3.18 mm - 14.27 mm
Pressure: 1.4 bar - 6.9 bar
... pneumatic needle
valves are equipped with a V-tip for rapid opening and closing. For flow regulation, hand-operated needle
valves with regulating tips are recommended.
Technical data
Nominal diameter: ...
WEH FluidTech GmbH
DN: 3.18 mm
Pressure: 1.4 bar
Temperature: -73 °C - 232 °C
... both directions, WEH® needle valves perform this function with absolute reliability. The valves are extremely smooth-running and durable, as the valve needle and the rotating valve spindle ...
WEH FluidTech GmbH
DN: 2.5 mm
Pressure: 2 bar - 10 bar
Temperature: 0 °C - 60 °C
... Microvalves with plug button 3/2 NO or NC with several actuation options, mechanical or manual. Thanks to the usage of the adaptor all actuators can be mounted on microvalves and it is also possible to combine two microvalves to obtain functions 5/2 ...
A&T Fluid solutions
DN: 0.125 in - 0.5 in
Pressure: 2 bar - 10 bar
Temperature: -10 °C - 70 °C
... The quick exhaust valve allows for rapid air evacuation from the cylinder to increase its speed. It is recommended to mount it directly on the cylinder’s air supply. ...
A&T Fluid solutions
DN: 0.125 in - 1 in
Pressure: 2 bar - 10 bar
Temperature: -20 °C - 180 °C
... The VRX quick exhaust valves from Airwork, when mounted on a pneumatic cylinder, allow for rapid pressure release from within the cylinder. Thanks to the material they are made from, 316L stainless steel, they are suitable for use in ...
A&T Fluid solutions
DN: 16 mm
... lever-operated, with position indicator Butterfly valve in action In-line valve VS 16, stainless steel, small flange KF DN 16 The VS und VS C series valves are butterfly-type valves. ...
VACUUBRAND
DN: 16 mm
... Ball valve in action Ball valve VKE 16, stainless steel, KF DN 16 Valves of the VK series are sturdy isolation devices for the rough and fine vacuum range. A precisely machined ball with a hole through ...
VACUUBRAND
DN: 16 mm
Temperature: 0 °C - 150 °C
... dimensions of the VE valve are the same as elbow with corresponding nominal width High vacuum bellow valve in action Bellow sealed angle valve VE, stainless steel, KF DN 16 High vacuum, helium ...
VACUUBRAND
Pressure: 10 bar - 500 bar
... max. operating pressure 500 bar, min. operating pressure 10 bar. Type of actuation: manual Application: For single acting cylinders. CETOP 3 adaptation. ...
Pressure: 400 bar
... Cylinder body made of steel, phosphatized. Remaining parts made of tempering steel. Valve seat and piston are hardened and ground. This valve is leak free. The stop valve shuts the flow from P to A ...
DN: 6 mm
... The hand valve provides bubble tight shut-off time after use. The valve is directly attached into the plate with O-ring seal. ...
DN: 50 mm - 150 mm
... Whether it is silos, mills or extraction systems, our slide valves enable a safe isolation, and are also available for demanding CIP, dust or gas applications. The REDEX® slide valve is suitable for the isolation of fully ...
DN: 50 mm - 500 mm
... Whether it is silos, mills or extraction systems, our slide valves enable a safe isolation, and are also available for demanding CIP, dust or gas applications. The RSV slide valve is suitable for the isolation of fully ...
Pressure: 2.5 bar - 15 bar
Temperature: 0 °C - 60 °C
... Elcometer AGV Automatic General Valve ensures precision abrasive control and fail-safe shut down of both the blast stream and media flow. The Elcometer AGV Automatic General Valve utilises all the benefits of our General ...
Elcometer
DN: 15 mm
Pressure: 2.5 bar - 15 bar
Temperature: 0 °C - 60 °C
... can opt for the Mini General Valve. Alternatively, the larger 25mm (1") General Valve can be installed to most Blast Machines available on the market. Precise Abrasive Metering When developing Elcometer's General ...
Elcometer
Pressure: 15 bar
... can opt for the Mini General Valve. Alternatively, the larger 25mm (1") General Valve can be installed to most Blast Machines available on the market. Precise Abrasive Metering When developing Elcometer's General ...
Elcometer
DN: 0.5, 0.75, 1, 1.25, 1.5 in
Pressure: 25 bar
... For oxygen, for the manual interruption of gas supply lengths: 65, 120 mm weights: 1.030 / 1.800 g Approvals EN 9539 ...
WITT-Gasetechnik
DN: 6 mm - 40 mm
Pressure: 1.5 bar
... range of ball valves with a variety of body and seal material combinations with female thread, male thread or flanged connections. The ball valve dimensions conform to the DIN standard (installation length and connection). Ball ...
WITT-Gasetechnik
DN: 6 mm - 40 mm
Pressure: 40 bar
... range of ball valves with a variety of body and seal material combinations with female thread, male thread or flanged connections. The ball valve dimensions conform to the DIN standard (installation length and connection). Ball ...
WITT-Gasetechnik
DN: 0 mm - 1.5 mm
Pressure: 0 bar - 34.7 bar
... The needle valve is an adjustable orifice, which can be used to control flow rates, mini-cylinders, nozzles, timing circuits, filling heads, bleed vents, and in many other applications. The adjusted flow remains stable even during temperature ...
Beswick Engineering Co, Inc.
DN: 1 mm - 1.1 mm
Pressure: 0 bar - 13.8 bar
... The MSV series slide sleeve valve provides an efficient in-line three-way valve. When the sleeve is moved to the “ON” position, fluid is allowed to pass through the valve. When the sleeve is moved to ...
Beswick Engineering Co, Inc.
DN: 0.375, 0.07 in
Pressure: 0 psi - 250 psi
... to protect a pneumatic actuator such as a chuck, press, or gripper from sudden bursts of high pressure. The internal needle valve restricts the initial movement of the actuator to a user defined speed, and then opens up upon sensing back ...
Beswick Engineering Co, Inc.
DN: 0.25 in - 0.75 in
Pressure: 0 psi - 250 psi
Temperature: -18 °C - 70 °C
... ANVER’s two-way ball valves are compact and easy to use. Activated manually for basic on/off pressure control or vacuum applications, these durable ball valves provide a tight connection for optimal stop/flow function ...
ANVER Vacuum System Specialists
DN: 0.375 in - 1 in
Pressure: 0 psi - 250 psi
Temperature: -18 °C - 121 °C
... release • Forged body design, extends the life of the ball valve • Optimum flow design. • Blow-out proof stem • Locking handle for added safety • More economical and compact than 3-way valves • Suitable for all ...
ANVER Vacuum System Specialists
DN: 0.125 in - 0.5 in
Pressure: 0 psi - 150 psi
Temperature: -18 °C - 70 °C
... ANVER Slide Valves are manually controlled, 3-way functioning valves that vent the downstream vacuum or pressure when the valve is turned to the OFF position. This provides a simple, yet effective way ...
ANVER Vacuum System Specialists
DN: 8, 6, 4, 10 mm
Pressure: 0.2 MPa - 1 MPa
Temperature: 0 °C - 60 °C
... Industry's First! It enables same control as the cylinder with shock absorber. (Patent no. 5578502) Shock absorber is not required. Two-stage exhaust flow rate adjustment is realized. By using 2nd stage exhaust speed to be as cushion (brake), controlling ...
NIHON PISCO CO., Ltd.
DN: 3 mm - 12 mm
Pressure: 0.1 MPa - 1 MPa
Temperature: 0 °C - 60 °C
... Flow rate can be set with indicator. Reducing the task of initial flow settings or their maintenance / replacement. The scales are on the side (upper / lower) and the top. Flow rate is proportional to the knob turns. 2 types with different flow range ...
NIHON PISCO CO., Ltd.
DN: 4, 6, 8 mm
Pressure: 0.1 MPa - 0.9 MPa
Temperature: 0 °C - 60 °C
... Orifice Flow Controller Preset Flow Control Valve (Tamper-Proof) preset flow control valve makes constant-flow in one direction and unrestricted flow in the opposite by an orifice restrictor. It is best suited for use ...
NIHON PISCO CO., Ltd.
DN: 0 mm - 10,000 mm
... significantly lighter diaphragm valve bodies.
SISTO Armaturen S.A.
DN: 6 mm - 300 mm
Pressure: 20 bar
... The two-way valve bodies have one single valve seat and are made of forged stainless steel material. They are available with weld ends or clamps according to the standards (DIN 11850, ISO 4200/1127, ASME BPE). Other ...
SISTO Armaturen S.A.
DN: 15 mm - 200 mm
Pressure: 16 bar
Temperature: -20 °C - 160 °C
... Weir-type diaphragm valve to DIN/EN with flanged ends, threaded socket ends or socket weld ends, in straight-way pattern; shut-off and sealing to atmosphere by supported and confined diaphragm; body with coating or lining, position indicator ...
SISTO Armaturen S.A.
DN: 0.125 in - 0.5 in
... Manual valve for single acting cylinders (bypass knob) 3 way / 2 position Manual valve for single acting cylinders 3 way / 3 position Manual valve for oil return cylinders 4 way / 3 position Solenoid ...
Pressure: 700 bar
... Manual valve for oil return cylinders 4 way / 3 position Solenoid valve for oil return cylinders 4 way / 3 position ...
DN: 0.25, 0.375 in
Pressure: 700 bar
... Inline unidirectional check valve. It blocks the flow in one direction while allowing it to move in the opposite direction Inline pilot-operate check valve: blocks the flow in one direction allowing it to move in the ...
Pressure: 1.2 bar - 10 bar
Flow rate: 0 l/min - 300 l/min
AWF
DN: 150 mm - 180 mm
AWF
AWF
DN: 0.25 in
Temperature: 0 °C - 120 °C
... Technical Data The CVA series is used in where the pressure at the inlet is variable and the pressure at the outlet is constant. The CVD series is used in where the pressure at the inlet is constant and the pressure at the outlet is variable. Flow Rate: Liquid: ...
Golden Mountain Enterprise
DN: 0.5 in - 3 in
Pressure: 600 psi
... Investment casting, ASTM-A351, CF8M, Class 600, inside screw and screwed bonnet wedge dise. Intégral seat, Nonrising stem, and Handwheel. Body - CF8M Bonnet - CF8M Disc - CF8M Stem - SUS316 Gasket - Teflon Snap Ring - SUS316 Washer - SUS316 Packing ...
Golden Mountain Enterprise
DN: 0.5 in - 2 in
Pressure: 600 psi
... * Investment casting, ASTM-A351, CF8M, Class 600, Screwed bonnet, Beveled dise, Intégral seat, Rising-stem, and Handwheel. Body - CF8M Bonnet - CF8M Stem - SUS316 Gasket - Teflon Disc - CF8M Packing - Teflon Gland - SUS316 Cap Nut - CF8M Handle ...
Golden Mountain Enterprise
DN: 15 mm - 250 mm
Pressure: 10 bar - 100 bar
Temperature: -60 °C - 350 °C
... The sliding gate control valve type 8021 in reinforced GS3 design with integrated positioner is suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. can perfectly be handled. Size: DN ...
Schubert & Salzer Control Systems GmbH
DN: 15 mm - 250 mm
Pressure: 10 bar - 40 bar
Temperature: -60 °C - 350 °C
... The sliding gate control valve type 8043 in a reinforced version and long design with piston actuator and integrated positioner is due to its compact design universally applicable for neutral and aggressive media in the chemical industry, ...
Schubert & Salzer Control Systems GmbH
DN: 15 mm - 125 mm
Pressure: 10 bar - 40 bar
Temperature: -60 °C - 230 °C
... This compact motor valve is used in a wide range of process engineering control tasks. It is particularly characterised by its very short design. Most media such as steam, fluids, gases, etc. can be excellently controlled with it. This ...
Schubert & Salzer Control Systems GmbH
the best suppliers