AIR Logic valves

DN: 6, 4, 8 mm
Pressure: 0 bar - 20 bar
Temperature: 0 °C - 140 °C

... Römer flow and stop valve program consists of throttle, shut-off and check valves. The function fittings offer fine adjustment possibilities for the precise regulation of fluid flows. Throttle valves ...

DN: 2.5 mm
Pressure: 3 bar - 10 bar
Temperature: 0 °C - 140 °C

AVS Römer pressure relief valves are used for protection in closed circuits. When the set response pressure is exceeded, the valve opens and discharges the fluid.

DN: 4 mm
Pressure: 0 bar - 6 bar
Temperature: 0 °C - 140 °C

... anti-vacuum membrane solenoid valve and relief valve regulates negative pressure via an anti-vacuum membrane, with a relief valve opening in the event of overpressure and relieving upward ...

DN: 450 mm - 1,400 mm
Pressure: 16 bar
Temperature: -180 °C - 650 °C

Ball valves are often subjected to extreme conditions, especially when used in pipelines. To withstand even the highest loads, Böhmer ball valves are therefore welded through the entire cross-section. ...

DN: 3 mm - 1,400 mm
Pressure: 10 bar - 800 bar
Temperature: 180 °C - 650 °C

Split body ball valves up to a nominal diameter of 56 inch are a integral component part of the Böhmer product line. Ball valves of this design are well suited for extremely abrasive and corrosive fluids. Böhmer ...

DN: 3 mm - 1,400 mm
Pressure: 10 bar - 800 bar
Temperature: -180 °C - 650 °C

... long periods of time. Böhmer ball valves are manufactured with experience, great know-how and high quality standards. Thanks to these ingredients, Böhmer ball valves are ideal for use in underground pipelines. Our ...

DN: 10 mm
Pressure: 320 bar
Flow rate: 400 l/min

3/2-way valve cartridge for electric, direct and pilot controls applicable. Connection: DN10

DN: 3 mm
Pressure: 320 bar
Flow rate: 20 l/min

The pilot valve is suitable for applications with permanent pressure. The valve is fitted on the left and right side with a locking lever.

DN: 10 mm
Pressure: 0 bar - 510 bar
Flow rate: 0 l/min - 400 l/min

The pressure relief valve for connecting the DN10 has a maximum liter capacity of 400 l /min. The operating pressure can be set max.510 bar.

DN: 0.25 in - 1 in
Pressure: 413 bar
Temperature: -200 °C - 500 °C

Needle valve with conical stem/shutter for precision and stable close, for use in general applications. Ideal for flow regulation by strangulation liquid and gases systems sealing and venting . Thanks to its stability, ...

DN: 0.25 in - 1 in
Pressure: 413 bar
Temperature: -200 °C - 500 °C

Needle valve with conical stem/shutter for precision and stable close, for use in general applications. Ideal for flow regulation by strangulation liquid and gases systems sealing and venting . Thanks to its stability, ...

DN: 0.375, 0.25, 0.5 in
Pressure: 690 bar
Temperature: -200 °C - 500 °C

High pressure systems Needle valve with conical stem/shutter for precision and stable close, for use in general applications. Ideal for flow regulation by strangulation liquid and gases systems sealing and venting . Thanks ...

DN: 1.5 in - 4 in

... Opening/closing: by 3W solenoid pilot valve •Applications : For water distribution •To remove operation of hydraulic valve by electric command Description G500-EL model valve ...

DN: 0.75 in - 2 in
Pressure: 0.3 bar - 10 bar
Temperature: 5 °C - 50 °C

... & NPT Pressure range0 3 to 10bar Temperature rangeFluid : 5ºC to 50ºC (no freezing) Materials in contact with mediaMain Valve: Reinforced Nylon Diaphragm: NR Seals: Buna – N Spring: Stainless Steel AISI 300 series

DN: 0.25 in - 0.5 in
Pressure: 0.5 bar - 10 bar
Temperature: -10 °C - 80 °C

... See table Temperature rangeFluid : 5ºC to 50ºC (no freezing) Ambient : -10ºC to 50ºC Materials in contact with mediaMain Valve: Brass, Stainless Steel AISI 316 Seals: NBR MediaAir, gas, water, fuel, oil etc

Dredge Gate Valve FEATURES: The dredge valve is designed in such a way that there are no fasteners inside the body Dredge valve is made of fabricated high tensile steel and cast steel The ...

DN: 50 mm - 3,000 mm
Pressure: 10 bar - 100 bar

Pressure / flow control valves. Main features : ■ significant reduction in turbulence, vibration and noise ■ fine regulation of the entire range of flow, made possible by the customized trim ■ high precision in ...

DN: 250 mm - 3,400 mm
Pressure: 10 bar - 100 bar

... the flow is controlled by the movement of the sleeve of the valve against the fixed cone. The fixed cone valve discharges the raw water of dams to free air, chamber or underwater level. This valve ...

DN: 100 mm - 2,200 mm
Pressure: 10 bar - 64 bar

... stilling basin and then into the downstream channel. Nencini also designs and engineers the stilling well related to the valve. Applications ■ hydraulic power plants ■ turbine by-pass ■ controlled discharges.

Pressure: 0 Pa - 2,000 Pa
Temperature: 0 °C - 1,000 °C

As for industrial round valves, square valves are also designed taking into account the pressures and temperatures of use. The industrial square valves do not have a standard dimension, ...

DN: 250 mm - 3,000 mm

The dapò valves are widely used where a regulation of the flow rate or a partialization of the air flows is required. Dapò adjustment valves with diameters from 250 mm up to 3000 mm are possible. For ...

... Rimor manufactures guillotine valves for all those applications where it does not have to be present – with the valve open – no impediment to the flow of fluid eg shavings and so on, this can not be achieved ...

DN: 15 mm - 100 mm
Pressure: 16 bar
Temperature: 120 °C

Brass gate valve Novo • - Non rising stem, solid wedge, screwed ends • - Used for water, petroleum • - Green color handwheel • - BS 21 / ISO 228-1-2000 threads standard • - Max working pressure: 16 bar ~ 16 kg/cm² • ...

DN: 15, 20 mm
Pressure: 16 bar
Temperature: 120 °C

Brass ball valve Novo • - Brass ball valve, screwed ends • - Used for water, steam, gas, petroleum • - Blue color handwheel • - BS 21 / ISO 228-1-2000 threads standard • - Max working pressure: ...